Half-cock
Encyclopedia
Half-cock is a technical firearms term referring to the position of the hammer
where the hammer is partially but not completely cocked. Many firearms, particularly older firearms, had a notch cut into the hammer allowing half-cock, as this position would neither allow the gun to fire nor permit the hammer-mounted firing pin to rest on a live percussion cap
or cartridge. The purpose of the half-cock position has variously been used either for loading a firearm, or, as a safety-mechanism, or for both reasons.
Early flintlock
s had required a half-cock position to prime the pan, in preparation for firing the firearm, after loading the main chamber.
Some early types of revolvers, such as the Colt 1851 Navy Revolver
, required the user to place the hammer at half-cock to permit rotation of the cylinder to load the firearm. On such firearms, the standard practice was not to load all 6 chambers and leave the hammer at half-cock, but, rather, to load only 5 of 6 chambers by standard safety practice, and stow the dropped hammer on an unloaded chamber. Nonetheless, some users did use the half-cock notch as a very early safety on such revolvers when all 6 chambers were loaded, often to a dangerous and unintended consequence.
Likewise, some early types of repeating lever-action cartridge rifles, such as the Winchester Model 94 rifle, had a half-cock position that was intended to serve as a safety mechanism, to keep the hammer away from the firing pin while holding the rifle when a round was chambered, such as when in a blind awaiting game to appear. Although the practice is today deprecated, the half-cock notch position on such rifles was formerly used by many hunters as a safety when carrying the loaded rifle with a round chambered while hunting. The half-cock position of the hammer did not serve a purpose while loading such firearms.
The half-cock notch most commonly worked through insertion of a spring-loaded thin metal plate into a slot cut into the tumbler, the tumbler being variously either part of the hammer or mechanically attached to the pivot-point of the hammer, depending on the particular firearm under discussion. When the tumbler/hammer rotated quickly from full-cock, the spring-loaded metal plate could not engage into the slot cut into the tumbler, and the firearm could fire since the hammer would fully rotate. When the tumbler/hammer rotated slowly from full-cock, such as when engaging the half-cock notch, the metal plate would slide into the slot cut in the tumbler, thereby preventing the hammer/tumbler from rotating fully, hence preventing the hammer from falling and the gun from firing.
In practice, the half-cock notch was often prone to breakage when used as an early safety mechanism, whereby the tumbler would have part of the metal around the slot shear away, thereby removing the fragile safety mechanism, and permitting the hammer to fall and the firearm to fire. This could occur from accidentally dropping the loaded firearm onto its half-cocked hammer but once.
The still commonly-used English expression of "going off half-cocked" derives from the failure of the half-cock mechanism to keep the hammer from falling and the subsequent failure to prevent a firearm from firing when unintended.
Hammer (firearm)
thumb|150px|Hammer with an integral [[firing pin]] on a [[S&W Model 13]] revolver The hammer of a firearm was given its name for both resemblance and functional similarity to the common tool...
where the hammer is partially but not completely cocked. Many firearms, particularly older firearms, had a notch cut into the hammer allowing half-cock, as this position would neither allow the gun to fire nor permit the hammer-mounted firing pin to rest on a live percussion cap
Percussion cap
The percussion cap, introduced around 1830, was the crucial invention that enabled muzzleloading firearms to fire reliably in any weather.Before this development, firearms used flintlock ignition systems which produced flint-on-steel sparks to ignite a pan of priming powder and thereby fire the...
or cartridge. The purpose of the half-cock position has variously been used either for loading a firearm, or, as a safety-mechanism, or for both reasons.
Early flintlock
Flintlock
Flintlock is the general term for any firearm based on the flintlock mechanism. The term may also apply to the mechanism itself. Introduced at the beginning of the 17th century, the flintlock rapidly replaced earlier firearm-ignition technologies, such as the doglock, matchlock and wheellock...
s had required a half-cock position to prime the pan, in preparation for firing the firearm, after loading the main chamber.
Some early types of revolvers, such as the Colt 1851 Navy Revolver
Colt 1851 Navy Revolver
The Colt Revolving Belt Pistol of Naval Caliber , later known as the Colt 1851 Navy or Navy Revolver, is a cap and ball revolver. It was designed by Samuel Colt between 1847 and 1850. It remained in production until 1873, when revolvers using fixed metallic cartridges came into widespread use...
, required the user to place the hammer at half-cock to permit rotation of the cylinder to load the firearm. On such firearms, the standard practice was not to load all 6 chambers and leave the hammer at half-cock, but, rather, to load only 5 of 6 chambers by standard safety practice, and stow the dropped hammer on an unloaded chamber. Nonetheless, some users did use the half-cock notch as a very early safety on such revolvers when all 6 chambers were loaded, often to a dangerous and unintended consequence.
Likewise, some early types of repeating lever-action cartridge rifles, such as the Winchester Model 94 rifle, had a half-cock position that was intended to serve as a safety mechanism, to keep the hammer away from the firing pin while holding the rifle when a round was chambered, such as when in a blind awaiting game to appear. Although the practice is today deprecated, the half-cock notch position on such rifles was formerly used by many hunters as a safety when carrying the loaded rifle with a round chambered while hunting. The half-cock position of the hammer did not serve a purpose while loading such firearms.
The half-cock notch most commonly worked through insertion of a spring-loaded thin metal plate into a slot cut into the tumbler, the tumbler being variously either part of the hammer or mechanically attached to the pivot-point of the hammer, depending on the particular firearm under discussion. When the tumbler/hammer rotated quickly from full-cock, the spring-loaded metal plate could not engage into the slot cut into the tumbler, and the firearm could fire since the hammer would fully rotate. When the tumbler/hammer rotated slowly from full-cock, such as when engaging the half-cock notch, the metal plate would slide into the slot cut in the tumbler, thereby preventing the hammer/tumbler from rotating fully, hence preventing the hammer from falling and the gun from firing.
In practice, the half-cock notch was often prone to breakage when used as an early safety mechanism, whereby the tumbler would have part of the metal around the slot shear away, thereby removing the fragile safety mechanism, and permitting the hammer to fall and the firearm to fire. This could occur from accidentally dropping the loaded firearm onto its half-cocked hammer but once.
The still commonly-used English expression of "going off half-cocked" derives from the failure of the half-cock mechanism to keep the hammer from falling and the subsequent failure to prevent a firearm from firing when unintended.