ITUpSAT1
Encyclopedia
ITUpSAT1 is a single CubeSat
built by Faculty of Aeronautics and Astronautics of the Istanbul Technical University
. It was launched on September 23, 2009 using PSLV from India
and became the first Turkish university satellite to orbit the Earth. It is expected to have a 6 month.
It is a picosatellite with side lengths of 10 cm and a mass of 1 kg.
The overall objectives are to provide a hands-on project environment for the students at ITU under faculty guidance. The mission goals are to capture imagery of the CMOS payload and to study the behavior of the passive stabilization system of the CubeSat.
Design of a deployable antenna system for a CubeSat: The base concept is shown in Figure 4 after investigating a number of various alternatives (Ref. 1). The pin mechanism selected includes bases to attach the antennas and pins to wrap them around. The pins and bases are attached to the solar panels with small screws. The cables are routed to a connector outside for connection to the antennas.
In addition, ITUpSat-1 features a beacon for easy identification and continuous reporting of critical telemetry. Unlike the other transceiver, it will always be on during the orbit and will be transmitting identification and simple telemetry in CW (e.g. Morse code) every two minutes. This means anyone with the knowledge of the orbital parameters (in particular the amateur radio community) can easily pick up our signal. The beacon has a 100 mW RF output capacity.
The launch site is the SDSC‐SHAR (Satish Dhawan Space Center-Sriharikota) on the east coast of India. The primary payload on the flight is OceanSat-2 of ISRO (Indian Space Research Organization) with a launch mass of 960 kg. Further secondary payloads on this flight are:
The camera can be operated in VGA/QVGA (Video Graphics Array/Quarter Video Graphics Array) modes, transfer images in 8/16 bit modes and can be controlled over the I2C bus.
CubeSat
A CubeSat is a type of miniaturized satellite for space research that usually has a volume of exactly one liter , has a mass of no more than 1.33 kilograms, and typically uses commercial off-the-shelf electronics components...
built by Faculty of Aeronautics and Astronautics of the Istanbul Technical University
Istanbul Technical University
Istanbul Technical University is an international technical university located in Istanbul, Turkey. It is the world's third oldest technical university dedicated to engineering sciences as well as social sciences recently, and is one of the most prominent educational institutions in Turkey...
. It was launched on September 23, 2009 using PSLV from India
India
India , officially the Republic of India , is a country in South Asia. It is the seventh-largest country by geographical area, the second-most populous country with over 1.2 billion people, and the most populous democracy in the world...
and became the first Turkish university satellite to orbit the Earth. It is expected to have a 6 month.
It is a picosatellite with side lengths of 10 cm and a mass of 1 kg.
The overall objectives are to provide a hands-on project environment for the students at ITU under faculty guidance. The mission goals are to capture imagery of the CMOS payload and to study the behavior of the passive stabilization system of the CubeSat.
Spacecraft
The spacecraft structure was purchased from Pumpkin Inc. of San Francisco, CA, consisting of aluminum 6061&5052 material (CubeSat Kit by Pumpkin Inc.). There are 3 identical side faces and one face with access ports. The spacecraft stabilization concept is discussed under Payload.EPS (Electrical Power Subsystem)
The EPS consists of face-mounted solar panels, a regulator board and associated batteries. The system is able to charge itself (maximum power point tracking) and provide a regulated 3.3 V and 5 V bus service.Design of a deployable antenna system for a CubeSat: The base concept is shown in Figure 4 after investigating a number of various alternatives (Ref. 1). The pin mechanism selected includes bases to attach the antennas and pins to wrap them around. The pins and bases are attached to the solar panels with small screws. The cables are routed to a connector outside for connection to the antennas.
OBC (On-board Computer)
The FM430 flight module of Pumpkin Inc. is being used. The FM430 is a compact solution for harsh environment systems. It has an SD (Secure Digital) card interface, one USB (Universal Serial Bus) port and external power supply connector. Also an interface to MHX series radio modems from Microhard Systems is available on the flight module. The FM430 is equipped with an MSP430F1611 microcontroller, a 16 bit 8 MHz low power microcontroller from Texas Instruments. It has many peripherals such as I2C (Inter-Integrated Communication), SPI (Serial Peripheral Interface), UART (Universal Asynchronous Receiver/Transmitter) buses, and also supports DMA (Direct Memory Access). It has a flash memory of 55 kB and 10 kB of RAM. The microcontroller unit consumes 100 mW of power at most.RF communications
The primary on-board communication system is the MHX-425 transceiver from Microhard Systems. This frequency hopping spread spectrum radio which works in the UHF band has adjustable hopping patterns, a high sensitivity (-115 dBm), and output power of up to 1 W (437.325 MHz, GFSK modulation), the data rate is 19.2 kbit/s. The transceiver interfaces directly to the on-board computer, it has a mass of about 80 gram.In addition, ITUpSat-1 features a beacon for easy identification and continuous reporting of critical telemetry. Unlike the other transceiver, it will always be on during the orbit and will be transmitting identification and simple telemetry in CW (e.g. Morse code) every two minutes. This means anyone with the knowledge of the orbital parameters (in particular the amateur radio community) can easily pick up our signal. The beacon has a 100 mW RF output capacity.
Launch
ITUpSat-1 was launched on Sept. 23, 2009 as a secondary payload on a PSLV launcher of ISRO (launch provider: Antrix Corporation). The SPL (Single Picosatellite Launcher) system of Astrofein (Astro und Feinwerktechnik Adlershof GmbH, Berlin, Germany) is being used to deploy the 4 CubeSats. The launch service interface for all CubeSats is provided by ISIS (Innovative Solutions In Space BV) from Delft, The Netherlands.The launch site is the SDSC‐SHAR (Satish Dhawan Space Center-Sriharikota) on the east coast of India. The primary payload on the flight is OceanSat-2 of ISRO (Indian Space Research Organization) with a launch mass of 960 kg. Further secondary payloads on this flight are:
- BeeSat (Berlin Experimental Educational Satellite), a CubeSat of the TUB (Technical University of Berlin), Berlin, Germany
- UWE-2 (University of Würzburg Experimentalsatellit-2), Würzburg, Germany
- SwissCube, a CubeSat of Ecole Polytechnique Federale de Lausanne, Lausanne, Switzerland
- Rubin-9.1 and Rubin-9.2 nanosatellites of OHB-System, Bremen, Germany.
Orbit
Sun-synchronous near circular orbit, altitude = 720 km, inclination = 98.28º, period = 99.31 min, the local equatorial crossing time is at 12:00 hours.Sensor complement
The CubeSat features two payloads. The first one is a sensor suite with an IMU and a magnetometer, and the second one is a low-resolution CMOS imager. The two payloads share a microcontroller and are physically on the same PCB representing the uppermost circuit of the electronics stack of the satellite.Payload 1
This subsystem represents the attitude sensing and passive stability hardware. It consists of three gyros, a three-axis accelerometer both from Analog Devices in addition to a three-axis magnetometer (Honeywell), and an AlNiCo magnet. The magnetometer will help to counter the inherent bias and drifts of inertial sensors and provide measurement updates for a filtered and corrected solution of the attitude. The analog-digital conversion of all the sensor outputs is done by a PIC microprocessor which also has the task of grouping the measurements into a packet and sending them over the I2C bus to the OBC for downlink transmission.Payload 2
Payload 2 is a low-resolution CMOS camera with a detector array of 640 x 480 pixels (COTS imager based on the OV7620 image sensor). The objective is to take snapshot imagery. An interface board is designed to integrate camera with the MSP430F1611 microcontroller.The camera can be operated in VGA/QVGA (Video Graphics Array/Quarter Video Graphics Array) modes, transfer images in 8/16 bit modes and can be controlled over the I2C bus.
Ground segment
A ground station was built at ITU for the operations (monitoring and control services) of ITUpSat-1. The MHX modem (Microhard Systems) is also installed in the ground station for communication with the satellite's nominal communication system.External links
- ITUpSAT1, ITU Space Systems Design and Test Laboratory
- ITUpSAT1 Gallery