The Kawasaki Triples were a range of 250 cc to 750 cc motorcycles Kawasaki exported from 1969 to 1980. The engines were air-cooled, three cylinder, two-stroke with two exhaust pipes exiting on the right side of the bike, and one on the left.

Model history

The first Kawasaki Triple was the 500 cc H1 Mach III

Kawasaki H1 Mach III

The Kawasaki H1 Mach III was a high-performance two-stroke 500cc production motorcycle manufactured by Kawasaki Motorcycle Corporation. It was sold in the U.S. and abroad from 1969 through 1975.-History:...

, introduced in late 1968. The original H1 was unique for using a CDI ignition

Capacitor discharge ignition

Capacitor discharge ignition or thyristor ignition is a type of automotive electronic ignition system which is widely used in outboard motors, motorcycles, lawn mowers, chainsaws, small engines, turbine-powered aircraft, and some cars...

 which operated through an automotive style distributor

Distributor

A distributor is a device in the ignition system of an internal combustion engine that routes high voltage from the ignition coil to the spark plugs in the correct firing order. The first reliable battery operated ignition was developed by Dayton Engineering Laboratories Co. and introduced in the...

. The H1 offered a high power-to-weight ratio for the time, but had generally poor handling and weak drum brakes front and rear. It was the quickest production motorcycle at the time. When motorcycle journalists expressed some disbelief, Kawasaki suggested they take a new H1 to the drag strip. Using a regular production model with only 7 miles on it, Tony Nicosia ran the quarter mile in 12.96 seconds at 100.7 mph (45 m/s) for the press to witness. The official figure was 12.4 secs by Mike Wenzel - quite believable on a well run in machine. Tony Nicosia set many world records with Kawasaki triples over the following years, including some land speed records at Bonneville Salt Flats.

In 1972, the 750 cc Kawasaki H2 Mach IV

Kawasaki H2 Mach IV

The Kawasaki H2 Mach IV was a 750 cc 3-cylinder two-stroke production motorcycle manufactured by the Kawasaki. The H2 was a Kawasaki triple sold from 1972 through 1975....

 was introduced and was essentially a scaled-up version of the H1 500. A stock H2 was rated at 12.0 secs for the quarter mile. Updated with more power and better front disc brakes, the H2 became the undisputed king of the streets, even beating legendary muscle cars of the era such as the Plymouth Hemi Cuda. It was notoriously dangerous, being prone to up-and-over wheelies and speed wobbles. The dangerous handling characteristics arising from its mediocre frame design caused it to be nicknamed the "Widowmaker" by motorcycle enthusiasts of the 1970s.

Modifications

A prototype liquid-cooled H2 was created in the late 1970s in either Australia or New Zealand.

The ability to cheaply modify the engines for higher performance by porting the cylinders, milling the cylinder heads, and installing expansion chamber exhausts maintained their popularity for some time in drag racing. An H2 holds the record for the first 7-second single engined two stroke of any kind, with a standing quarter-mile of 7.776 seconds at 170 mph (76 m/s) (NOS), ridden by Brian Pretzel of Redline Motorsports, engine built by Garth Glumm of Flow Research, also the engine builders of the fastest normally aspirated at 156.79 mph (70.1 m/s) (IHRA-Bristol Tn.-1991). The quickest reed-valve converted, normally aspirated 750 cc motorcycle with a standing quarter-mile of 8.24 seconds at 153 mph held by Joe Bird of Fremont Nebraska.

In 1974, the 350 cc S2 was expanded to a 400 cc S3. In addition, the model range was toned down in performance. The H2 ceased production in 1975, and the model line became the KH series in 1976. United States production stopped in 1976, while the 250 cc KH-250 and 400 cc KH-400 continued in Europe and elsewhere until 1980.

The S1 was popular for some time as a budget performance bike in England because of its small size, and the fact that at this point in time it was legal for learners to ride. The entire S series of motorcycles used breaker point ignition, which was more reliable than the early CDI ignition and much cheaper to repair or replace.

Kawasaki Triples were air-cooled, and the crankshafts were pressed together. This made it possible to cut an engine apart, press up extra sections of the crankshaft, re-weld different sections of the cases, and make multi-cylindered motorcycles. The ignition system and carburetors had to be redone. Four-cylinder 1,000 cc H2s were known to exist,
but the most common bikes to be modified were the S series, with 5- to 7-cylinder models being built, and at least one "V-6" (two three cylinder banks feeding into a common transmission). There even exists a 48 cylinder bike made up of 250 cc parts. These bikes were more of a machinist's skill exercise than a practical development. They were impractical because the engine was made much wider and the clutch and gearbox were put under more strain.

The 500 cc H1 also benefitted from the marketing genius of Kawasaki. They identified their target customers perfectly. Many US bikers under 30 years of age simply wanted to be the fastest kids on the block. The cost of a production of a two stroke engine was significantly less than that of a four stroke engine, and for many years Kawasaki managed to keep the list price for the H1 under the magical $1,000 barrier. Competing bikes from Norton and Triumph were over $1,200, and slower. For a while Kawasaki even dropped the CDI and reverted to the cheaper contact breaker ignition in order to keep the price under $1,000.

Model summary

1969
H1 500 cc white w/blue stripes, distributor CDI ignition, drum front brake, "Mach III 500" badge on side cover and "electronic ignition" decal on oil tank. Early 69 models had bridged port intake design, with "windowed" carbs. Late 1969 saw the introduction of the Charcoal Grey model, but a common misconception is the charcoal grey model is called a 1969 model, it is NOT a 1969 model and is indeed a 1970 model. Kawasaki paperwork that came with the bikes, and the sales brochures confirm this. This has been spread by many in order to add value to their bikes by being able to call them a first year model when they are not. The red and white model replaced the peacock grey model due to poor sales.

1970
H1 500 cc

1971
H1A 500 cc, style redesign without the Mach "III" badge

1972
Entire line introduced, intended to be similar in style, with the "swooping" racing stripes on the tank that distinguished the triples.

• S1 250 cc,
• S2 350 cc, drum front brake
• H1B 500 cc, orange, disc front brake, CDI dropped for breaker points, and a front disc brake.
• H1C had CDI instead of the points on an H1B, and a front drum brake as opposed to the disc on the earlier H1B. Also a few cosmetic changes.
• H2 750 cc, front disc brake, CDI ignition with one igniter unit per cylinder.

1973

• S1A 250 cc
• S2A 350 cc
• H1D 500 cc Adopted H2's CDI ignition and the styling that would be used on the later 1974 models.
• H2A 750 cc

1974
All models restyled with a new cleaner design that resembled the Kawasaki Z-1, with an instrument "pod" rather than separate instruments. All models revised for more civilized performance at the expense of raw power.

• S1B 250 cc front drum brake.
• S3 400 cc disc front brake, restyled cylinder head design for better cooling.
• H1E 500 cc
• H2B 750 cc

1975

• S1C 250 cc
• S3A 400 cc
• H1F 500 cc
• H2C 750 cc

1976

• H2 dropped from line, models renamed "KH" to match the "KZ" line of four strokes.
• KH-250 250 cc.
• KH-400 400 cc.
• KH-500 500 cc.

1977-1980
Only surviving models are the KH-250 and KH-400.

External links

• Kawasaki Triple at the Open Directory Project
  Open Directory Project
  The Open Directory Project , also known as Dmoz , is a multilingual open content directory of World Wide Web links. It is owned by Netscape but it is constructed and maintained by a community of volunteer editors.ODP uses a hierarchical ontology scheme for organizing site listings...