.gif)
Mikoyan-Gurevich I-250 (N)
Encyclopedia
The Mikoyan-Gurevich I-250 (a.k.a. Samolet N) was a Soviet
fighter aircraft developed as part of a crash program in 1944 to develop a high-performance fighter to counter German
turbojet-powered aircraft such as the Messerschmitt Me-262. The Mikoyan-Gurevich design bureau decided to focus on a design that used something more mature than the jet engine, which was still at an experimental stage in the Soviet Union, and chose a mixed-power solution with the VRDK motorjet
powered by the Klimov VK-107
V12 engine
. While quite successful when it worked, with a maximum speed of 820 km/h (509.5 mph) being reached during trials, production problems with the VRDK fatally delayed the program and it was canceled in 1948 as obsolete.
, Sukhoi
, Yakovlev
and Mikoyan-Gurevich
design bureaux (OKB
s) to develop and build jet aircraft with the utmost dispatch. Aware of earlier problems encountered with other novel propulsion systems such as ramjet
s both Sukhoi and Mikoyan-Gurevich chose to use the VRDK (Vozdushno-Reaktivnyy Dvigatel' Kompressornyy — Air-reactive compressed engine) jet booster engine that had been under development since 1942.
The VRDK was a motorjet
, a rudimentary type of jet engine
where an external power source drove the engine's compressor. It forced air into the stainless steel combustion chamber where fuel was sprayed from seven nozzles and ignited to exhaust out the variable rear nozzle. In the I-250 a 1650 hp Klimov VK-107
R V-12
piston engine was used as the primary powerplant. After takeoff a clutch at the end of the crankshaft could be engaged which drove a step up gearbox with a ratio of 13:21 to an extension shaft that powered the compressor of the VRDK. The air for the compressor was fed through a long duct that ran from the inlet underneath the propeller spinner, thence under the engine and through the belly of the aircraft. This duct also fed air to the oil cooler near the engine, but the water radiator was positioned behind the compressor to maximize airflow over it. A secondary duct led from the main duct to the VK-107's supercharger; when the VRDK was running the secondary duct diverted some of that additional air to the supercharger which boosted the engine's output to 2500 hp at 7000 m (22,966 ft). The increased airflow over the engine radiator helped to dump the engine's excess heat into the exhaust stream. However the VRDK was limited to only ten minutes' operating time per sortie
, which meant that it was useless weight during the rest of the flight.
The I-250 was a low-wing, all-metal aircraft with a monocoque
fuselage. Other than the VRDK the aircraft was largely conventional in layout, although the cockpit
was set very far back in the fuselage, almost to the base of the vertical tail. The two-spar
wings had a thickness of 10% to preserve aileron control and avoid tip stall. They were fitted with Frise ailerons and slotted flap
s. Fuel was contained in a 412 litres (870.7 US pt) fuselage tank and a 100 litres (211.3 US pt) tank in each wing. The conventional landing gear
mainwheels had a levered suspension and retracted inwards. The tail wheel retracted aft into the very small ventral fin. The VK-107A engine initially drove a 3.1 metres (10.2 ft) VISh-105SV propeller.
The NKAP had asked Mikoyan to begin preliminary design work on a high-altitude interceptor in January 1944, but ordered two prototypes of an all-metal interceptor using the VRDK for testing in February and March 1945. The aircraft was to reach an altitude of 5000 m (16,404.2 ft) in 4.5 minutes with full power and 5.5 minutes using the piston engine alone. Its maximum speed was to be 810 km/h (503.3 mph) at 7000 m (22,966 ft) with full power and 700 km/h (435 mph) at 7000 m (22,966 ft) using the VK-107 by itself. Its intended armament was one 23 mm (0.905511811023622 in) autocannon
and two 12.7 mm (0.5 in) machine gun
s. To assist Mikoyan TsAGI
was ordered to provide help with aerodynamic and stress calculations and to test a full-size mockup in their wind tunnel in one month's time. TsIAM was ordered to deliver three VRDK engines with 9 kilonewtons (9,000 N) at 7000 m (22,966 ft) with a specific fuel consumption of 1200 kg (2,645.5 lb) per hour. The plane was designated I-250 by the NKAP; but the internal OKB designation was N.
The NKAP approved the preliminary specifications of the I-250 on 19 September 1944 which included a maximum speed of 825 km/h (512.6 mph) a take-off weight of 3500 kg (7,716.2 lb) and a time to 5000 metres (16,404 ft) of 3.9 minutes. A mock-up was inspected on 26 October and rejected because of the poor cockpit layout, although this decision was reversed because the fuselage of the first prototype was too far along for major changes that would have significantly delayed the program. That same month the combustion chamber was sent to TsIAM for testing which revealed it to be too weak. The complete powerplant was tested in December, but the drive shaft connecting them failed several times.
The first prototype was completed on 26 February 1945, although the VRDK was not yet ready. It was fitted with a new 3.1 metres (10.2 ft) AV-10P-60 propeller before making its first flight on 4 April according to Gordon and Komissarov, although Belyakov and Marmain say 3 March. It was armed with three 20 mm Berezin B-20
cannon with 160 rounds each. One gun was fitted on each side of the nose and the third fired through the hollow propeller shaft. The VRDK was tested for the first time on 8 April in a dive, attaining a speed of 710 km/h (441.2 mph), but a leak was found in the oil cooler after landing and the VRDK had to be returned to the factory for repairs. The VRDK was reinstalled by 14 April, but was still troublesome. It twice reached 809 km/h (502.7 mph) at about 7000 m (22,966 ft) during these early tests, but its service life had been exceeded by 30 May and it had to be returned to TsIAM, which postponed any further tests until the second aircraft was finished.
The unarmed second prototype was completed on 19 May, but did not make its first flight until 26 May. It was later discovered to have several major defects, including an oil leak from the VRDK compressor's sleeve. The VRDK's designer was summoned in an attempt to solve its problems although not all of these were design issues. The first prototype was grounded for most of June to remedy magneto
problems and to add extra air intakes to cool the spark plugs. It attained a speed of 820 km/h (509.5 mph) at 6700 m (21,982 ft) on 3 July. Unfortunately its port tailplane failed at low altitude two days later, killing the test pilot, Alexandr Deyev, when his parachute failed to open in time. Post-crash analysis revealed that he had exceeded the airframe's G limit
while maneuvering.
Despite the accident, a pre-production batch of ten aircraft was ordered on 27 July 1945 as it was felt that mixed-power aircraft would be of some use easing the transition of pilots from piston-engine fighters to jet-engined ones. At the same time Sukhoi's Su-5
was cancelled as it was judged inferior to the I-250.
In the meantime the horizontal stabilizer of the second prototype was strengthened and it resumed flying on 20 July. The pilot complained of excess torque pull to the right so the vertical stabilizer was enlarged by 0.63 m² (0.753473729169681 sq yd), but this was just one of numerous problems, and it was not ready to pass State acceptance trials without more development work on the powerplant. However, the second prototype continued flight testing until 12 July 1946 when an engine fire forced an emergency landing and it was damaged beyond repair.
The order for the pre-production I-250s had been placed with Factory No. 381 in Moscow for two aircraft to be delivered in September, three more in October and the remainder by the end of the year. This proved to be very optimistic and it was revised to a single aircraft by the end of the year. The airframe was completed on this revised schedule, but its engine was not ready in time. The factory management was much criticized for these problems which were not entirely under their control as changes to the design and drawings were constant. The criticism was not limited to just the I-250 program as the other jet programs could not be developed as fast as the leadership wanted as well and Alexei Shakhurin, the head of MAP (Ministry of Aviation Industry) and its NKAP predecessor since 1940, was arrested in March 1946 as a sign of their displeasure. The new Minister severely reprimanded the designer of the VRDK and three factory directors on 13 April 1946 and set up a commission to determine why Factory No. 381 and TsIAM had failed to meet their deadlines. He refused to accept its findings as it apportioned blame fairly evenly among those responsible for the production program and he had the director of Factory No. 381 and his quality control manager arrested for industrial sabotage.
Despite these production problems and the fact that the I-250 had yet even to be submitted for State acceptance trails, an order had been placed for fifty more aircraft on 26 February (these aircraft have been referred to as the MiG-13, which presumably would have been their designation if they had actually entered service). A new deadline of 5 July 1946 was set for the delivery of the first pre-production aircraft, but it was stymied, again, for a lack of an engine. By this time seven airframes had been completed, but all lacked engines. The first I-250 was finally accepted on 8 August and flown for the first time three days later, although its engine seals failed and a number of ignition cables were scorched. The engine replacement and repairs forced the aircraft to miss its scheduled appearance at the Tushino Air Display. It was handed over to the NII VVS (Air Force Institute) on 15 September to finally begin its State acceptance tests. All ten aircraft had been delivered by 30 October, although construction number 3810107 (Factory No. 381, first batch, seventh aircraft) was used as a static test airframe and 3810110 became a static engine testbed.
Stalin
convened a meeting on 29 November 1946 to settle the future policy on jet fighters for the VVS and PVO. The Mikoyan-Gurevich MiG-9
was selected as the primary fighter with the Yakovlev Yak-15
relegated to conversion training and familiarization. The imminent availability of British jet engines and access to German jet technology and engineers meant that there was no longer any need for mixed-power aircraft, but Stalin insisted that the I-250 finish its trials and that the tooling and drawings should be retained along with unassembled parts even though the program was cancelled.
Completion of the trials would be delayed until May 1947 when the trials of the VRDK itself would be completed and Mikoyan tried to sell the aircraft to Naval Aviation
for use as escorts for torpedo bombers. Additional fuel tanks were fitted in the wings and fuselage of 3810102 to carry an additional 218 litres (461 US pt) of fuel and the capacity of the oil tank was increased to 78 litres (165 US pt). These changes increased its empty weight to 3028 kg (6,675.6 lb) and its take-off weight to 3931 l (8,307.7 US pt). A new round of State trials began on 9 October 1947, but these were delayed by bad weather and reliability issues. Only six flights totaling two hours and twenty-five minutes had been completed by 21 January 1948 and the VRDK had only been run for a minute and half during a ground test. The I-250 was unsurprisingly declared to have failed the trials on 3 April 1948.
Soviet Union
The Soviet Union , officially the Union of Soviet Socialist Republics , was a constitutionally socialist state that existed in Eurasia between 1922 and 1991....
fighter aircraft developed as part of a crash program in 1944 to develop a high-performance fighter to counter German
Germany
Germany , officially the Federal Republic of Germany , is a federal parliamentary republic in Europe. The country consists of 16 states while the capital and largest city is Berlin. Germany covers an area of 357,021 km2 and has a largely temperate seasonal climate...
turbojet-powered aircraft such as the Messerschmitt Me-262. The Mikoyan-Gurevich design bureau decided to focus on a design that used something more mature than the jet engine, which was still at an experimental stage in the Soviet Union, and chose a mixed-power solution with the VRDK motorjet
Motorjet
A motorjet is a rudimentary type of jet engine which is sometimes referred to as thermojet, a term now commonly used to describe a particular and completely unrelated pulsejet design.- Design :...
powered by the Klimov VK-107
Klimov VK-107
|-See also:-Bibliography:* Gunston, Bill. World Encyclopedia of Aero Engines. Cambridge, England. Patrick Stephens Limited, 1989. ISBN 1-85260-163-9...
V12 engine
V12 engine
A V12 engine is a V engine with 12 cylinders mounted on the crankcase in two banks of six cylinders, usually but not always at a 60° angle to each other, with all 12 pistons driving a common crankshaft....
. While quite successful when it worked, with a maximum speed of 820 km/h (509.5 mph) being reached during trials, production problems with the VRDK fatally delayed the program and it was canceled in 1948 as obsolete.
Design and development
By January 1944 the Soviets were aware of successful British and American jet aircraft projects and that the Germans were about to deploy jet and rocket-propelled aircraft of their own. The GKO ordered on 18 February that the NKAP (People's Commissariat for Aviation Industry) centralize jet research under its control and that the NKAP was to present proposals to alleviate the situation within a month. As a result of this meeting the NKAP ordered the LavochkinLavochkin
NPO Lavochkin is a Russian aerospace company. It is a major player in the Russian space program, being the developer and manufacturer of the Fregat upper stage, as well as interplanetary probes such as Phobos Grunt...
, Sukhoi
Sukhoi
Sukhoi Company is a major Russian aircraft manufacturer, headquartered in Begovoy District, Northern Administrative Okrug, Moscow, famous for its fighters...
, Yakovlev
Yakovlev
The Yak Aircraft Corporation is a Russian aircraft designer and manufacturer...
and Mikoyan-Gurevich
Mikoyan
Russian Aircraft Corporation MiG , or RSK MiG, is a Russian joint stock company. Formerly Mikoyan-and-Gurevich Design Bureau , then simply Mikoyan, it is a military aircraft design bureau, primarily designing fighter aircraft...
design bureaux (OKB
OKB
OKB is a transliteration of the Russian acronym for "Опытное конструкторское бюро" - Opytnoe Konstructorskoe Byuro, meaning Experimental Design Bureau...
s) to develop and build jet aircraft with the utmost dispatch. Aware of earlier problems encountered with other novel propulsion systems such as ramjet
Ramjet
A ramjet, sometimes referred to as a stovepipe jet, or an athodyd, is a form of airbreathing jet engine using the engine's forward motion to compress incoming air, without a rotary compressor. Ramjets cannot produce thrust at zero airspeed and thus cannot move an aircraft from a standstill...
s both Sukhoi and Mikoyan-Gurevich chose to use the VRDK (Vozdushno-Reaktivnyy Dvigatel' Kompressornyy — Air-reactive compressed engine) jet booster engine that had been under development since 1942.
The VRDK was a motorjet
Motorjet
A motorjet is a rudimentary type of jet engine which is sometimes referred to as thermojet, a term now commonly used to describe a particular and completely unrelated pulsejet design.- Design :...
, a rudimentary type of jet engine
Jet engine
A jet engine is a reaction engine that discharges a fast moving jet to generate thrust by jet propulsion and in accordance with Newton's laws of motion. This broad definition of jet engines includes turbojets, turbofans, rockets, ramjets, pulse jets...
where an external power source drove the engine's compressor. It forced air into the stainless steel combustion chamber where fuel was sprayed from seven nozzles and ignited to exhaust out the variable rear nozzle. In the I-250 a 1650 hp Klimov VK-107
Klimov VK-107
|-See also:-Bibliography:* Gunston, Bill. World Encyclopedia of Aero Engines. Cambridge, England. Patrick Stephens Limited, 1989. ISBN 1-85260-163-9...
R V-12
V12 engine
A V12 engine is a V engine with 12 cylinders mounted on the crankcase in two banks of six cylinders, usually but not always at a 60° angle to each other, with all 12 pistons driving a common crankshaft....
piston engine was used as the primary powerplant. After takeoff a clutch at the end of the crankshaft could be engaged which drove a step up gearbox with a ratio of 13:21 to an extension shaft that powered the compressor of the VRDK. The air for the compressor was fed through a long duct that ran from the inlet underneath the propeller spinner, thence under the engine and through the belly of the aircraft. This duct also fed air to the oil cooler near the engine, but the water radiator was positioned behind the compressor to maximize airflow over it. A secondary duct led from the main duct to the VK-107's supercharger; when the VRDK was running the secondary duct diverted some of that additional air to the supercharger which boosted the engine's output to 2500 hp at 7000 m (22,966 ft). The increased airflow over the engine radiator helped to dump the engine's excess heat into the exhaust stream. However the VRDK was limited to only ten minutes' operating time per sortie
Sortie
Sortie is a term for deployment or dispatch of one military unit, be it an aircraft, ship, or troops from a strongpoint. The sortie, whether by one or more aircraft or vessels, usually has a specific mission....
, which meant that it was useless weight during the rest of the flight.
Monocoque
Monocoque is a construction technique that supports structural load by using an object's external skin, as opposed to using an internal frame or truss that is then covered with a non-load-bearing skin or coachwork...
fuselage. Other than the VRDK the aircraft was largely conventional in layout, although the cockpit
Cockpit
A cockpit or flight deck is the area, usually near the front of an aircraft, from which a pilot controls the aircraft. Most modern cockpits are enclosed, except on some small aircraft, and cockpits on large airliners are also physically separated from the cabin...
was set very far back in the fuselage, almost to the base of the vertical tail. The two-spar
Spar (aviation)
In a fixed-wing aircraft, the spar is often the main structural member of the wing, running spanwise at right angles to the fuselage. The spar carries flight loads and the weight of the wings whilst on the ground...
wings had a thickness of 10% to preserve aileron control and avoid tip stall. They were fitted with Frise ailerons and slotted flap
Flap (aircraft)
Flaps are normally hinged surfaces mounted on the trailing edges of the wings of a fixed-wing aircraft to reduce the speed an aircraft can be safely flown at and to increase the angle of descent for landing without increasing air speed. They shorten takeoff and landing distances as well as...
s. Fuel was contained in a 412 litres (870.7 US pt) fuselage tank and a 100 litres (211.3 US pt) tank in each wing. The conventional landing gear
Conventional landing gear
thumb|The [[Piper PA-18|Piper Super Cub]] is a popular taildragger aircraft.thumb|right|A [[Cessna 150]] converted to taildragger configuration by installation of an after-market modification kit....
mainwheels had a levered suspension and retracted inwards. The tail wheel retracted aft into the very small ventral fin. The VK-107A engine initially drove a 3.1 metres (10.2 ft) VISh-105SV propeller.
The NKAP had asked Mikoyan to begin preliminary design work on a high-altitude interceptor in January 1944, but ordered two prototypes of an all-metal interceptor using the VRDK for testing in February and March 1945. The aircraft was to reach an altitude of 5000 m (16,404.2 ft) in 4.5 minutes with full power and 5.5 minutes using the piston engine alone. Its maximum speed was to be 810 km/h (503.3 mph) at 7000 m (22,966 ft) with full power and 700 km/h (435 mph) at 7000 m (22,966 ft) using the VK-107 by itself. Its intended armament was one 23 mm (0.905511811023622 in) autocannon
Autocannon
An autocannon or automatic cannon is a rapid-fire projectile weapon firing a shell as opposed to the bullet fired by a machine gun. Autocannons often have a larger caliber than a machine gun . Usually, autocannons are smaller than a field gun or other artillery, and are mechanically loaded for a...
and two 12.7 mm (0.5 in) machine gun
Machine gun
A machine gun is a fully automatic mounted or portable firearm, usually designed to fire rounds in quick succession from an ammunition belt or large-capacity magazine, typically at a rate of several hundred rounds per minute....
s. To assist Mikoyan TsAGI
TsAGI
TsAGI is a transliteration of the Russian abbreviation for Центра́льный аэрогидродинами́ческий институ́т or "Tsentralniy Aerogidrodinamicheskiy Institut", the Central Aerohydrodynamic Institute....
was ordered to provide help with aerodynamic and stress calculations and to test a full-size mockup in their wind tunnel in one month's time. TsIAM was ordered to deliver three VRDK engines with 9 kilonewtons (9,000 N) at 7000 m (22,966 ft) with a specific fuel consumption of 1200 kg (2,645.5 lb) per hour. The plane was designated I-250 by the NKAP; but the internal OKB designation was N.
The NKAP approved the preliminary specifications of the I-250 on 19 September 1944 which included a maximum speed of 825 km/h (512.6 mph) a take-off weight of 3500 kg (7,716.2 lb) and a time to 5000 metres (16,404 ft) of 3.9 minutes. A mock-up was inspected on 26 October and rejected because of the poor cockpit layout, although this decision was reversed because the fuselage of the first prototype was too far along for major changes that would have significantly delayed the program. That same month the combustion chamber was sent to TsIAM for testing which revealed it to be too weak. The complete powerplant was tested in December, but the drive shaft connecting them failed several times.
The first prototype was completed on 26 February 1945, although the VRDK was not yet ready. It was fitted with a new 3.1 metres (10.2 ft) AV-10P-60 propeller before making its first flight on 4 April according to Gordon and Komissarov, although Belyakov and Marmain say 3 March. It was armed with three 20 mm Berezin B-20
Berezin B-20
The Berezin B-20 was a 20 mm caliber autocannon used by Soviet aircraft in World War II.-Development:The B-20 was created by M.E. Berezin in 1944 by chambering his Berezin UB 12.7 mm machine gun for the 20 mm rounds used by the ShVAK cannon...
cannon with 160 rounds each. One gun was fitted on each side of the nose and the third fired through the hollow propeller shaft. The VRDK was tested for the first time on 8 April in a dive, attaining a speed of 710 km/h (441.2 mph), but a leak was found in the oil cooler after landing and the VRDK had to be returned to the factory for repairs. The VRDK was reinstalled by 14 April, but was still troublesome. It twice reached 809 km/h (502.7 mph) at about 7000 m (22,966 ft) during these early tests, but its service life had been exceeded by 30 May and it had to be returned to TsIAM, which postponed any further tests until the second aircraft was finished.
The unarmed second prototype was completed on 19 May, but did not make its first flight until 26 May. It was later discovered to have several major defects, including an oil leak from the VRDK compressor's sleeve. The VRDK's designer was summoned in an attempt to solve its problems although not all of these were design issues. The first prototype was grounded for most of June to remedy magneto
Magneto (electrical)
A magneto is an electrical generator that uses permanent magnets to produce alternating current.Magnetos adapted to produce pulses of high voltage are used in the ignition systems of some gasoline-powered internal combustion engines to provide power to the spark plugs...
problems and to add extra air intakes to cool the spark plugs. It attained a speed of 820 km/h (509.5 mph) at 6700 m (21,982 ft) on 3 July. Unfortunately its port tailplane failed at low altitude two days later, killing the test pilot, Alexandr Deyev, when his parachute failed to open in time. Post-crash analysis revealed that he had exceeded the airframe's G limit
G-force
The g-force associated with an object is its acceleration relative to free-fall. This acceleration experienced by an object is due to the vector sum of non-gravitational forces acting on an object free to move. The accelerations that are not produced by gravity are termed proper accelerations, and...
while maneuvering.
Despite the accident, a pre-production batch of ten aircraft was ordered on 27 July 1945 as it was felt that mixed-power aircraft would be of some use easing the transition of pilots from piston-engine fighters to jet-engined ones. At the same time Sukhoi's Su-5
Sukhoi Su-5
-See also:...
was cancelled as it was judged inferior to the I-250.
In the meantime the horizontal stabilizer of the second prototype was strengthened and it resumed flying on 20 July. The pilot complained of excess torque pull to the right so the vertical stabilizer was enlarged by 0.63 m² (0.753473729169681 sq yd), but this was just one of numerous problems, and it was not ready to pass State acceptance trials without more development work on the powerplant. However, the second prototype continued flight testing until 12 July 1946 when an engine fire forced an emergency landing and it was damaged beyond repair.
The order for the pre-production I-250s had been placed with Factory No. 381 in Moscow for two aircraft to be delivered in September, three more in October and the remainder by the end of the year. This proved to be very optimistic and it was revised to a single aircraft by the end of the year. The airframe was completed on this revised schedule, but its engine was not ready in time. The factory management was much criticized for these problems which were not entirely under their control as changes to the design and drawings were constant. The criticism was not limited to just the I-250 program as the other jet programs could not be developed as fast as the leadership wanted as well and Alexei Shakhurin, the head of MAP (Ministry of Aviation Industry) and its NKAP predecessor since 1940, was arrested in March 1946 as a sign of their displeasure. The new Minister severely reprimanded the designer of the VRDK and three factory directors on 13 April 1946 and set up a commission to determine why Factory No. 381 and TsIAM had failed to meet their deadlines. He refused to accept its findings as it apportioned blame fairly evenly among those responsible for the production program and he had the director of Factory No. 381 and his quality control manager arrested for industrial sabotage.
Despite these production problems and the fact that the I-250 had yet even to be submitted for State acceptance trails, an order had been placed for fifty more aircraft on 26 February (these aircraft have been referred to as the MiG-13, which presumably would have been their designation if they had actually entered service). A new deadline of 5 July 1946 was set for the delivery of the first pre-production aircraft, but it was stymied, again, for a lack of an engine. By this time seven airframes had been completed, but all lacked engines. The first I-250 was finally accepted on 8 August and flown for the first time three days later, although its engine seals failed and a number of ignition cables were scorched. The engine replacement and repairs forced the aircraft to miss its scheduled appearance at the Tushino Air Display. It was handed over to the NII VVS (Air Force Institute) on 15 September to finally begin its State acceptance tests. All ten aircraft had been delivered by 30 October, although construction number 3810107 (Factory No. 381, first batch, seventh aircraft) was used as a static test airframe and 3810110 became a static engine testbed.
Stalin
Joseph Stalin
Joseph Vissarionovich Stalin was the Premier of the Soviet Union from 6 May 1941 to 5 March 1953. He was among the Bolshevik revolutionaries who brought about the October Revolution and had held the position of first General Secretary of the Communist Party of the Soviet Union's Central Committee...
convened a meeting on 29 November 1946 to settle the future policy on jet fighters for the VVS and PVO. The Mikoyan-Gurevich MiG-9
Mikoyan-Gurevich MiG-9
The Mikoyan-Gurevich MiG-9 was the first Soviet turbojet fighter developed by Mikoyan-Gurevich in the years immediately after World War II. It used reverse-engineered German BMW 003 engines...
was selected as the primary fighter with the Yakovlev Yak-15
Yakovlev Yak-15
The Yakovlev Yak-15, NATO reporting name: Feather, USAF/DOD designation Type 2) was a first-generation Soviet turbojet fighter developed by the Yakovlev design bureau immediately after World War II. It used a reverse-engineered German Junkers Jumo 004 engine...
relegated to conversion training and familiarization. The imminent availability of British jet engines and access to German jet technology and engineers meant that there was no longer any need for mixed-power aircraft, but Stalin insisted that the I-250 finish its trials and that the tooling and drawings should be retained along with unassembled parts even though the program was cancelled.
Completion of the trials would be delayed until May 1947 when the trials of the VRDK itself would be completed and Mikoyan tried to sell the aircraft to Naval Aviation
Soviet Naval Aviation
Soviet Naval Aviation was a part of the Soviet Navy.- Origins :...
for use as escorts for torpedo bombers. Additional fuel tanks were fitted in the wings and fuselage of 3810102 to carry an additional 218 litres (461 US pt) of fuel and the capacity of the oil tank was increased to 78 litres (165 US pt). These changes increased its empty weight to 3028 kg (6,675.6 lb) and its take-off weight to 3931 l (8,307.7 US pt). A new round of State trials began on 9 October 1947, but these were delayed by bad weather and reliability issues. Only six flights totaling two hours and twenty-five minutes had been completed by 21 January 1948 and the VRDK had only been run for a minute and half during a ground test. The I-250 was unsurprisingly declared to have failed the trials on 3 April 1948.
Specifications (first prototype)