Mud motor
Encyclopedia
Mud motor refers to a Progressive Cavity Positive Displacement Pump
placed in the Drill string
to provide additional power to the bit while drilling. The PCPD Pump uses Drilling Fluid
(commonly referred to as Drilling Mud, or just Mud) to create eccentric motion in the power section of the motor which is transferred as concentric power to the drill bit (well)
. The Mud Motor uses different rotor and stator configurations to provide optimum performance for the desired drilling operation, typically increasing the number of lobes and length of power assembly for greater horsepower. In certain applications, compressed air, or other gas, can be used for Mud Motor input power. Normal rotation of the bit while using a Mud Motor can be from 60 rpm, to over 100 rpm.
The use of Mud Motors is greatly dependent on financial efficiency. In straight vertical holes, the mud motor may be used solely for increased Rate of Penetration (ROP), or to minimize erosion and wear on the drill string, since the drill string does not need to be turned as fast.
The majority of Mud Motor use is in the drilling of Directional Holes (see Directional Drilling
). Although other methods may be used to steer the bit to the desired target zone, they are more time consuming which adds to the cost of the well. Mud Motors can be configured to have a bend in them using different settings on the motor itself. Typical Mud Motors can be modified from 0 degrees to 4 degrees with approximately six increments in deviation per degree of bend. The amount of bend is determined by rate of climb needed to reach the target zone. By using a Measurement While Drilling (MWD) Tool, a directional driller can steer the bit to the desired target zone.
. Most of PCPD pump failures are due to this elastomer part. Having said that, the operating conditions and environment should not degrade or induce mechanical failure of the elastomer part for the life of the equipment. Unfortunately, the industry does not have elastomers that can last longer, resisting abrasive fluids and solids, and withstand deflections in operating temperatures. The most common elastomer grades used for this application are the NBR (Nitrile or Acrylonitrile Butadiene Rubber) grades, which perform moderately well. There is definitely a need for better elastomer compounds to reach areas which are not currently accessible by PCPs and also improve the life of current products.
Progressive cavity pump
A progressive cavity pump is a type of positive displacement pump and is also known as a progressing cavity pump, eccentric screw pump or even just cavity pump. It transfers fluid by means of the progress, through the pump, of a sequence of small, fixed shape, discrete cavities, as its rotor is...
placed in the Drill string
Drill string
A drill string on a drilling rig is a column, or string, of drill pipe that transmits drilling fluid and torque to the drill bit. The term is loosely applied as the assembled collection of the drill pipe, drill collars, tools and drill bit...
to provide additional power to the bit while drilling. The PCPD Pump uses Drilling Fluid
Drilling fluid
In geotechnical engineering, drilling fluid is a fluid used to aid the drilling of boreholes into the earth. Often used while drilling oil and natural gas wells and on exploration drilling rigs, drilling fluids are also used for much simpler boreholes, such as water wells. Liquid drilling fluid...
(commonly referred to as Drilling Mud, or just Mud) to create eccentric motion in the power section of the motor which is transferred as concentric power to the drill bit (well)
Drill bit (well)
A ', is a device attached to the end of the drill string that breaks apart, cuts or crushes the rock formations when drilling a wellbore, such as those drilled to extract water, gas, or oil....
. The Mud Motor uses different rotor and stator configurations to provide optimum performance for the desired drilling operation, typically increasing the number of lobes and length of power assembly for greater horsepower. In certain applications, compressed air, or other gas, can be used for Mud Motor input power. Normal rotation of the bit while using a Mud Motor can be from 60 rpm, to over 100 rpm.
Normal construction
Normal Mud Motor construction consists of a top sub, which connects the Mud Motor to the Drill String; the Power Section, which consists of the Rotor and Stator; the Transmission Section, where the eccentric power from the rotor is transmitted as concentric power to the bit; the Bearing Assembly which protects the tool from off bottom and on bottom pressures; and the bottom sub which connects the Mud Motor to the bit.The use of Mud Motors is greatly dependent on financial efficiency. In straight vertical holes, the mud motor may be used solely for increased Rate of Penetration (ROP), or to minimize erosion and wear on the drill string, since the drill string does not need to be turned as fast.
The majority of Mud Motor use is in the drilling of Directional Holes (see Directional Drilling
Directional drilling
Directional drilling is the practice of drilling non-vertical wells. It can be broken down into three main groups: Oilfield Directional Drilling, Utility Installation Directional Drilling Directional drilling (or slant drilling) is the practice of drilling non-vertical wells. It can be broken down...
). Although other methods may be used to steer the bit to the desired target zone, they are more time consuming which adds to the cost of the well. Mud Motors can be configured to have a bend in them using different settings on the motor itself. Typical Mud Motors can be modified from 0 degrees to 4 degrees with approximately six increments in deviation per degree of bend. The amount of bend is determined by rate of climb needed to reach the target zone. By using a Measurement While Drilling (MWD) Tool, a directional driller can steer the bit to the desired target zone.
Major disadvantage in oilfield applications
The PCPD stator, which is a major component of the pump, is usually lined with an elastomerElastomer
An elastomer is a polymer with the property of viscoelasticity , generally having notably low Young's modulus and high yield strain compared with other materials. The term, which is derived from elastic polymer, is often used interchangeably with the term rubber, although the latter is preferred...
. Most of PCPD pump failures are due to this elastomer part. Having said that, the operating conditions and environment should not degrade or induce mechanical failure of the elastomer part for the life of the equipment. Unfortunately, the industry does not have elastomers that can last longer, resisting abrasive fluids and solids, and withstand deflections in operating temperatures. The most common elastomer grades used for this application are the NBR (Nitrile or Acrylonitrile Butadiene Rubber) grades, which perform moderately well. There is definitely a need for better elastomer compounds to reach areas which are not currently accessible by PCPs and also improve the life of current products.
See also
- Drilling Mud
- Logging While DrillingLogging While DrillingLogging While Drilling is a technique of conveying well logging tools into the well borehole downhole as part of the bottom hole assembly ....
(LWD) - Measurement While DrillingMeasurement While DrillingMWD stands for Measurement While Drilling in the oil & gas industry. The simplest way to describe MWD is to relate it to the measurements a pilot takes. A pilot needs to know the direction they are flying , the angle they are fly at , and what type of skies they will be flying through...
(MWD)