T-44
Encyclopedia
The T-44 was a medium tank
first produced towards the end of the Second World War
by the Soviet Union
. It was the successor to the famous T-34
. Fewer than two thousand T-44s were built, but the design became the basis for the T-54/55
series of main battle tank
s, the most-produced tank of all time.
This design project was designated T-34M. It had enhanced armour protection, a three-man hexagonal turret, torsion bar suspension instead of Christie suspension
, road wheels with internal shock absorption, increased fuel capacity, and more main gun ammunition (100 rounds instead of 77 in standard T-34). The bow machine gun and driver's hatch switched positions on the glacis plate. In addition to six smaller wheels, the suspension of the T-34M had four return rollers. The original model V-2 12-cylinder diesel engine developing 500 hp (373 kW) was replaced by a new 12-cylinder diesel engine which produced 600 hp. It had a new 8-speed transmission system. It was the first tank design to feature transverse engine placement, which made it smaller than a standard T-34 and gave the crew more space.
The Zhdanov Metallurgical Factory manufactured five sets of armour plates for the hull of the T-34M and delivered them to Factory No. 183. However, early in 1941 work on the T-34M ceased as the production facilities were extremely busy with the mass production of the T-34. When the war with Nazi Germany
broke out the only sensible solution was to gradually improve the existing design.
During the battles on the Eastern Front
it became apparent that the Red Army needed a new medium tank. They requested that it should have better protection at a minimal increase of weight. In 1942 the T-43 tank design project began. It featured a new turret and shorter suspension which reduced the clearance between the roadwheels. However, it concentrated on increasing armour at a time when maintaining production and increasing firepower were more important. The T-43 was cancelled, but its new turret design was adapted to carry a larger 85 mm D-5T and later ZiS-S-53 gun in a new variant called the T-34-85. It marked the end of T-34 improvements as fitting 100 mm guns in T-34-100 prototypes proved unfeasible. (See T-34 variants
article for details).
in 1941), started working on a vehicle that would have improvement opportunities in the future, under a direct order from Joseph Stalin
. The intention was to retain the high mobility of the T-34 and provide it with heavier armour
protection against modern tank guns. In November 1943, the chief designer, A. A. Morozov, presented the overall design of the vehicle and a model of the tank, which received the designation T-44 (Ob'yekt 136). The first prototype was completed by January 1944 and two more were completed in February. The first two prototypes were armed with 85 mm D-5T guns and received the designation T-44-85, while the third prototype was armed with the 122 mm D-25-44T tank gun and received the designation T-44-122. The D-25-44T tank gun was very similar to the basic D-25 field gun, but differed in some minor details including fixed single-piece ammunition to increase the rate of fire and a double-baffle muzzle brake. What allowed fitting such powerful armament in a medium tank weighing 30 tonnes was the construction of the hull with an innovative placement of the engine. Unlike most tanks, in the T-44 the engine was placed perpendicular to the axis of the tank. The hull was designed without sponsons. It was also much wider which made the crew compartment bigger and allowed the turret to be placed over the center part of the vehicle. This reduced the overall length of the vehicle. The thickness of the armour was 75 mm on the front of the hull and 90 mm on the front of the turret. The side armour was 45 mm thick and could be reinforced by 30 mm thick additional armour plate. All three prototypes were powered by the V-2IS diesel engine which developed 500 hp (373 kW). This first generation of prototypes featured a raised cast driver's hatch with an opening vision flap as well as mounting bolts in a ring around the base of the gun tube.
Morozov's new medium tank design received a skeptical response. It was believed that putting a high-speed 12-cylinder engine with a working displacement of almost 40 liters perpendicular to the direction of travel would cause problems, including breaking the connecting rods. It was believed that decreasing the displacement of the engine compartment for the purpose of enlarging the fighting compartment was unnecessary and that moving the turret rearwards would limit the elevation angle of the main gun. However, it turned out that even though rotating the engine complicated the transmission by introducing an additional reduction gear - gear-train and fan drive, it also solved many problems. The cover of the engine and transmission compartment turned along with the radiator; this allowed easier access to the engine, transmission and batteries. The significant decrease in the length of the engine compartment allowed the turret to be moved rearwards, which in turn moved its rotation axis and the center of mass to the center of the hull, increased the accuracy of the main gun and decreased a chance that the turret could get stuck after getting hit in the turret ring with a projectile that ricocheted. The thickness of the frontal armor protection more than doubled without disturbing the center of mass or drastically increasing the weight of the tank. At the beginning of World War II the thickness of T-34 armor was considered enough. Improvements made to the T-34 during World War II included increasing the caliber of the gun (from 76.2 mm to 85 mm) and thickening the armor of the turret. No significant improvements were made to the hull. Increasing the size of the fighting compartment allowed the removal of floor ammunition stowage. The height of the tank was decreased by 300 mm, even though the turret remained almost the same. Removal of the conical pair in the transmission permitted fitting a more compact gear box and improved the control of the brakes and the steering clutch. Visibility from the driver's position was improved. The driver was protected from being splashed by water while the vehicle was fording. The new torsion bar suspension allowed easier crossing of rough ground.
The first trials of the T-44-122 prototype took place in February and March 1944, but were unsuccessful due to gun failure, and the gun was returned to the No. 9 factory for repair. In April and May 1944 the trials were resumed. Aside from standard trials, the T-44-122 was put in competitive trials against the captured German Panzerkampfwagen V Panther medium tank and the second of two first generation T-44-85 prototypes. The practical rate of fire was two to three rounds per minute due to the cramped turret and long, heavy ammunition. The vehicle had a very limited stowage of only 24 rounds and this was considered insufficient for a medium tank. As a result all further development of the T-44-122 prototype was cancelled.
Like the T-44-122 prototype, one of the two first-generation T-44-85 prototypes went through competitive trials against the captured German Panzerkampfwagen V Panther medium tank. The second of the two first-generation T-44-85 prototypes was put in competitive trials against the T-44-122 prototype. The second prototype uncovered additional faults in the design. By May 1944 two second-generation prototypes were being built. These featured the driver's position moved rearwards so that his hatch was partially on the hull roof. The driver's vision flap was reduced to a plain square flap with rounded lower corners, in line with the glacis plate. These prototypes had prominent collars at the base of the gun tube, without the mounting bolts which were present in the first generation prototypes. The two prototypes also have differences between each other. One prototype had a splashboard on the glacis plate while the other had a smooth uncluttered glacis plate. One of these prototypes passed trials at the NIBT proving grounds near Kubinka
in June and July 1944. This prototype weighed 31.3 tonnes and was armed with an 85 mm ZiS-S-53 gun. The turret front armour thickness was increased to 115 mm. Hulls side armour thickness was increased to 75 mm.
had moved back to Kharkiv
in Ukraine
. The hull upper front armour (glacis plate) thickness was increased to 90 mm and the turret front armour thickness was increased to 120 mm. Even though it was more heavily armoured, the weight went down to 30.7 tonnes. This vehicle had a new V-44 12-cylinder 4-stroke diesel engine of 520 hp (388 kW) at 1,800 rpm, which allowed the tank to travel at a speed of 60.5 km/h. This prototype had the splashboard on the glacis plate like one of the second generation T-44-85 prototypes. This prototype featured some other differences from the earlier prototypes, including the fact that drivers hatch was moved entirely to the roof of the hull and the vision flap was deleted from the design and replaced by a vision slot in the glacis plate. After trials conducted in August and September 1944 and after it received several upgrades (which increased the weight of the vehicle to 32 tonnes), the T-44A officially entered service with the Red Army on the 23 November 1944.
Even with its innovative technology and better armor protection, the T-44A still used an 85 mm ZiS-S-53 tank gun, the same as the one fitted on the T-34-85 medium tank. The army needed a new tank armed with a more powerful 100 mm gun. At the end of 1944 the designers had three types of 100 mm guns at their disposal which could considerably increase the firepower of the tank. These included the D-10 (which already proved itself in combat as it was used in SU-100 tank destroyer) as well as prototype ZiS-100 and LB-1 (LB stands for Lavrenty Beria). The T-44 tank armed with 100 mm tank gun originally received the designation T-44B. Two projects were started, both based on the T-44A. The development of the first one started in October 1944 at the design bureau of the Stalin Ural Tank Factory No. 183, located in Nizhny Tagil. The designing stage was completed in December. The prototype was ready in February 1945. The trials conducted between March and April gave positive results and the vehicle entered service with the Red Army as T-54. The tank had almost the same hull and drive train as the T-44A. Differences included thickened front armour (120 mm on the upper section and 90 mm on the lower section) and a different hatch and vision slot for the driver. The turret had increased diameter to 1800 mm. There was thicker armour (180 mm on the front, between 90 mm and 150 mm on the sides and 30 mm on the roof). The armament included the 100 mm D-10TK tank gun as well as two 7.62 mm GWT machine guns. The tank was powered by a new V-54 12-cylinder 38.88 liter water-cooled diesel engine developing 520 hp (388 kW) at 2,000 rpm. The fuel capacity was increased (530 liters in the internal fuel tank and 165 liters in the external fuel tank). The external fuel tanks were connected to the fuel system. The rubber rollers on the roadwheels were widened. The weight was increased to 35.5 tonnes, which reduced the maximal road speed to 43.5 km/h. The maximal road operational range increased to 360 km. Because of positive results seen in trials, it was decided to modernize the tank before starting production (for more details about it see the T-54/55 article) as well as to put the new tank's turret onto two modified serial T-44A tanks. This was done in 1945 and the two prototype tanks received the designation T-44-100. One of the prototypes was armed with a D-10TK tank gun while the other one was armed with a LB-1 tank gun. Like the second generation T-44-85 prototypes, the two T-44-100 prototypes had differences between each other. One prototype had a splashboard on the glacis plate while the other did not. They both had the 12.7 mm DShK anti-aircraft heavy machine gun fitted to the loader's hatch, 6 mm thick anti-HEAT sideskirts protecting the sides and two cylindrical fuel tanks in the back which increased the fuel capacity to 1035 liters. These cylindrical fuel tanks were later used on Soviet main battle tanks as additional fuel tanks. Further development of the T-44 was canceled and all the attention was directed towards the development of a new T-54 main battle tank.
protection against large-caliber tank guns. This was accomplished by adding thicker armour but reducing the internal volume of the hull. The T-44 had a lower profile than the T-34, and was potentially simpler to manufacture. Although the T-44 used many components of the T-34, it had a new hull, and a modified model V-2 diesel engine, suspension and transmission.
Reflecting trends in other designs in this period, the T-44 was designed without the hull radio operator/machine gunner position present in many older designs. This was done for a number of reasons. The extensive machine gun firing port in the glacis plate (which was present in T-34 medium tank) was a weak spot in the armour. In the T-34, this firing port and the driver's hatch were exploited during World War II by the Germans fighting the T-34s. Shooting the machine gun was ineffective as it was inaccurate due to obscured vision. It was considered inefficient to transfer reports through an additional member of the crew and therefore these duties were transferred to the commander. The space saved was used for a fuel tank and to increase the ammunition load. The driver's hatch was on the left side of the hull roof. The tank had an improved hull design, longer and wider than the T-34 but slightly lower thanks to the relocation of the air filter, with thicker armour, and was simpler to construct. The hull had a sloped glacis plate, vertical sides, and a slightly beveled rear. Most tanks had a splashboard on the glacis plate although there are pictures of T-44A tanks without them. It protected the upper part of the vehicle from splashes of mud or water. There were three mounts for rectangular stowage bins on the fenders (two on the right fender and one on the left fender). There were four mountings for cylindrical fuel tanks on the fenders (two per side). This was changed in the T-44M which used rectangular fuel cells.
During its service the tank proved to be not entirely adapted to winter conditions as due to an incomplete draining of the cooling system, caused by a water pump system that had been modified to reduce engine height. A small shaft would break after the impeller pump froze. The repair of the shaft, considering the field conditions, proved very impractical and required three people. Two people had to hold a third person by the legs and lower him into the engine bay, where he had to loosen the fastening and remove the broken shaft. Then, he was pulled out and lowered back down to install the new shaft. He was repeatedly lowered until the new part was secured. Another serious problem discovered during the winter conditions was that the crews of the T-44A suffered from frostbite because of the complete lack of a heating system. The driver was supposed to be protected from rain and snow by a removable tarp cover with a small glass window. However, this was not successful and its use was deemed impractical.
The T-44 had a compact torsion-bar suspension instead of the T-34's Christie
coil springs, although it retained the Christie method of engagement between the slotted drive wheel and track
lugs. The suspension had five large spoked road wheels and 'dead' 500 mm long track from the T-34. The hull and wheels were virtually identical to the early T-54 main battle tanks although the original T-44 had the T-34's 'spider' road wheels and a narrow, inset drive wheel at the rear. The T-44 was the last Soviet medium tank with paddle-type tracks. The mechanism for tensioning them was significantly better on the T-44 than it was on the T-34. On the T-34, first two lug-nuts on the crank had to be loosened and then the crank pounded with a sledge hammer in order to separate it from the hull. After the track was tensioned, the crank had to be set back in place with a sledge hammer. The whole process required up to three people. On the T-44, the same task could be carried out by one person, without the help of a sledge-hammer. The roadwheels were spaced evenly from each other except for a prominent gap between two of the roadwheels. The T-44-85 and T-44-122 prototypes had a gap between the second and third roadwheels like in the T-34 but the T-44A had a gap between the first and second roadwheels. This arrangement of wheels was continued in the T-54 and T-55 main battle tanks. The roadwheels sometimes started to 'fall home' after 2,500 km. To increase the service life of the road wheel, a slight camber of the paired road wheels was tried. However, this resulted in greater stress on the outer rollers. When the tank crosses 20 km of rough ground it can pick up about a ton of dirt along the way.
The new V-44 12-cylinder 4-stroke diesel engine, developing 520 hp (388 kW) at 1,800 rpm, was a more powerful version of the T-34's model V-2 with a new planetary manual 5-speed transmission system, filtration system, improved cooling system, horizontally placed water and oil pumps and an improved fuel system which increased its power output, although the tank retained the side clutches from the T-34. The new engine gave the T-44 a maximal road speed of 53 km/h and maximal cross country speed of 20 km/h to 25 km/h as well as maximal road range of 350 km. The engine could become worn out after the tank traveled 3,000 km. When that happened, the oil pressure would drop to 2-3 atmospheres and under heavy loads, the engine would start smoking, spewing out black smog out of the side of the tank. The engine deck had two transverse ventilation grilles at the rear. The exhaust port was on the rear left hand side of the hull. The tank could cross 1 m high vertical obstacles, 2.5 m wide trenches, 32° side slopes and 60° gradients and ford 1.3 m deep water obstacles without preparation.
Because driver's hatch was moved from the glacis plate and positioned so that he exited the vehicle perpendicularly instead of crawling out of the hatch, his seat received an elevating mechanism. While in a relatively safe area the driver could elevate his seat to look outside of the tank, providing greater visibility and easier access to the controls. While in combat the driver lowered his seat back into the tank and had to rely on the vision slot protected by triplex (three-layer glass). While in this position the pedals of the main clutch, the fuel supply, and incline brake were positioned much higher and the levers of the steering clutch and gear shifting became inconvenient to operate. Early examples had transmission problems. While the driver was switching gears, two gears could engage simultaneously, which caused a broken gear pinion. This and other gearbox related problems were solved in a 1961 T-44M modernization with the introduction of a gearbox from the T-54 main battle tank.
T-44A was armed with an 85 mm ZiS-S-53 tank gun as well as two 7.62 mm DTM light machine guns. One of these machine guns was mounted to fire through a tiny hole in the center of the glacis plate. Because the tank's crew did not include a radio operator/machine gunner, the driver operated this light machine gun. The gun was mounted in a fixed position and could only be aimed by turning the tank. The main gun was placed in a centrally placed turret along with a coaxially mounted 7.62 mm DTM light machine gun. The ZiS-S-53 tank gun could penetrate around 100 mm of armour at range of 1000 m. The gun could be elevated or depressed between -5° and +25°. It wasn't stabilized. Like in the T-34 and SU-76
SPG
, hot cartridge-cases were rolling under the feet of the crew. The crew was also subjected to gases from the main gun every time after it was fired. The tank carried 58 rounds for the 85 mm ZiS-S-53 tank gun and 1890 rounds for 7.62 mm DTM light machine guns.
The turret was cast, with a prominent horizontal casting seam, shaped like an elongated hexagon, with sloped sides and overhang all around. It resembled a longer, better armoured T-34-85 turret. It had a cast gun mantlet
with a small but prominent ring/collar around the base of the tank gun tube. The turret roof had a raised commander's cupola on the left and loader's hatch on the right with a low dome-shaped ventilator behind it. The turret was moved with an electric motor. The front armour of the turret was 120 mm thick while the side armour was 75 mm thick.
The hull was made of rolled welded steel. The glacis plate was 90 mm thick while the side armour was 75 mm and the bottom armour was 20 mm thick. T-44 tanks could be fitted with additional 30 mm thick armour plates on the sides of the hull and the turret. Additional spaced armour panels could be fitted to the sides of the hull.
The T-44A could be fitted with the PT-3 mine clearing device. It had a radio in the back of the turret with an antenna at the center of the left side of the turret. The vehicle was equipped with a submachine gun. The vehicle lacked an NBC (nuclear, biological and chemical) protection system and a night vision device.
and Prague Offensive
. The T-44A was not used operationally during World War II in Europe for several reasons, including the fact that the Red Army was not ready to accept a new tank because of lack of sufficient spares and technical specialists who could repair and maintain the new tanks as well as the fact that many of the tank crews would have to be retrained. However, three tanks were sent to the 100th Special Tank Company which tested them on the Eastern Front
. Many T-44As were immediately sent after they were produced in the Far East regions of the Soviet Union. The first tanks arrived there before the end of the war and were used operationally during the last three days of fighting. They continued to arrive after the war and eventually around 600 T-44As were stationed there.
Due to the Cold War, the USSR decided to keep the tank secret. It was never shown publicly during military parades and pictures were never shown publicly until the secrecy was dropped. There is almost no photographic evidence of T-44s stationed in East Germany or during the Soviet invasion of Hungary in 1956 although it is known that T-44s were sent there (there are only a small number of photos of T-44As in Hungary in existence).
In 1961, a number of T-44As were modernized with parts from the T-54 main battle tank and other upgrades and received the designation T-44M. In 1963, some T-44Ms were converted into T-44MK command tanks. In 1965 some T-44Ms were converted into BTS-4A armoured recovery vehicles. In 1966, a number of T-44As and T-44Ms received the "Cyclone" gun stabilizer and the designations T-44S and T-44MS, respectively. According to most sources T-44S, T-44M and T-44MS tanks remained in service with the Soviet Army until the end of the 1970s, when their usefulness as tanks had ended. It is possible that they remained in storage until the beginning of 1990s. Many T-44Ms were converted into artillery tractors, tank tractors and engineer tanks. A number of T-44A, T-44S, T-44M, T-44MK and T-44MS tanks were converted into fixed defensive positions; some of which are known to have been positioned on the border with the People's Republic of China
. Unlike most Soviet made weapons the T-44 wasn't exported.
After the cloak of secrecy was lifted in 1960s, when the tank was already becoming obsolete, it was used in the war movies: Father of a Soldier, Liberation
, Battle of Moscow
, Red Cherry
, The Star, and Downfall
. In the first, it was used to portray a T-34. In Liberation, Red Cherry, The Star, and Downfall it was visually modified with additional plates to resemble the Tiger I
heavy tank
. Some T-44 and T-34 tanks were visually modified to represent German Panzerkampfwagen IVs. They were made for Soviet era film studios and were used in a number of movies about battles on the Eastern Front
. They were also used during a 2004 re-enactment of the Battle of Moscow
. Some T-44As were given to military museums including one in Brest
in today's Belarus
. One of two T-44-100 prototypes is in the Kubinka Tank Museum
.
Medium tank
Medium tank was a classification of tanks; the medium being intermediate in size and weight and armament between heavy tanks and light tanks.The medium tank concept has been eclipsed by the main battle tank.-History:...
first produced towards the end of the Second World War
World War II
World War II, or the Second World War , was a global conflict lasting from 1939 to 1945, involving most of the world's nations—including all of the great powers—eventually forming two opposing military alliances: the Allies and the Axis...
by the Soviet Union
Soviet Union
The Soviet Union , officially the Union of Soviet Socialist Republics , was a constitutionally socialist state that existed in Eurasia between 1922 and 1991....
. It was the successor to the famous T-34
T-34
The T-34 was a Soviet medium tank produced from 1940 to 1958. Although its armour and armament were surpassed by later tanks of the era, it has been often credited as the most effective, efficient and influential design of World War II...
. Fewer than two thousand T-44s were built, but the design became the basis for the T-54/55
T-55
The T-54 and T-55 tanks were a series of main battle tanks designed in the Soviet Union. The first T-54 prototype appeared in March 1945, just before the end of the Second World War. The T-54 entered full production in 1947 and became the main tank for armored units of the Soviet Army, armies of...
series of main battle tank
Main battle tank
A main battle tank , also known as a battle tank or universal tank, is a tank that fills the heavy direct fire role of many modern armies. They were originally conceived to replace the light, medium, heavy and super-heavy tanks. Development was spurred onwards in the Cold War with the development...
s, the most-produced tank of all time.
Genesis
By the end of 1940, when production of the T-34 started, there were already plans to improve the vehicle's reliability and operational capabilities by adopting more modern technology.This design project was designated T-34M. It had enhanced armour protection, a three-man hexagonal turret, torsion bar suspension instead of Christie suspension
Christie suspension
The Christie suspension is a suspension system developed by American engineer Walter Christie for his tank designs. It allowed considerably longer movement than conventional leaf spring systems then in common use, which allowed his tanks to have considerably greater cross-country speed and a lower...
, road wheels with internal shock absorption, increased fuel capacity, and more main gun ammunition (100 rounds instead of 77 in standard T-34). The bow machine gun and driver's hatch switched positions on the glacis plate. In addition to six smaller wheels, the suspension of the T-34M had four return rollers. The original model V-2 12-cylinder diesel engine developing 500 hp (373 kW) was replaced by a new 12-cylinder diesel engine which produced 600 hp. It had a new 8-speed transmission system. It was the first tank design to feature transverse engine placement, which made it smaller than a standard T-34 and gave the crew more space.
The Zhdanov Metallurgical Factory manufactured five sets of armour plates for the hull of the T-34M and delivered them to Factory No. 183. However, early in 1941 work on the T-34M ceased as the production facilities were extremely busy with the mass production of the T-34. When the war with Nazi Germany
Nazi Germany
Nazi Germany , also known as the Third Reich , but officially called German Reich from 1933 to 1943 and Greater German Reich from 26 June 1943 onward, is the name commonly used to refer to the state of Germany from 1933 to 1945, when it was a totalitarian dictatorship ruled by...
broke out the only sensible solution was to gradually improve the existing design.
Eastern Front (World War II)
The Eastern Front of World War II was a theatre of World War II between the European Axis powers and co-belligerent Finland against the Soviet Union, Poland, and some other Allies which encompassed Northern, Southern and Eastern Europe from 22 June 1941 to 9 May 1945...
it became apparent that the Red Army needed a new medium tank. They requested that it should have better protection at a minimal increase of weight. In 1942 the T-43 tank design project began. It featured a new turret and shorter suspension which reduced the clearance between the roadwheels. However, it concentrated on increasing armour at a time when maintaining production and increasing firepower were more important. The T-43 was cancelled, but its new turret design was adapted to carry a larger 85 mm D-5T and later ZiS-S-53 gun in a new variant called the T-34-85. It marked the end of T-34 improvements as fitting 100 mm guns in T-34-100 prototypes proved unfeasible. (See T-34 variants
T-34 variants
The T-34 medium tank is one of the most-produced and longest-lived tanks of all time.Identification of T-34 variants can be complicated. Turret castings, superficial details, and equipment differed between factories. New features were added in the middle of production runs or retrofitted to older...
article for details).
First generation
In the autumn of 1943 the design bureau of the Stalin Ural Tank Factory No. 183, located in Nizhny Tagil (in the Ural Mountains, where most of the Soviet tank industry had been evacuated after Operation BarbarossaOperation Barbarossa
Operation Barbarossa was the code name for Germany's invasion of the Soviet Union during World War II that began on 22 June 1941. Over 4.5 million troops of the Axis powers invaded the USSR along a front., the largest invasion in the history of warfare...
in 1941), started working on a vehicle that would have improvement opportunities in the future, under a direct order from Joseph Stalin
Joseph Stalin
Joseph Vissarionovich Stalin was the Premier of the Soviet Union from 6 May 1941 to 5 March 1953. He was among the Bolshevik revolutionaries who brought about the October Revolution and had held the position of first General Secretary of the Communist Party of the Soviet Union's Central Committee...
. The intention was to retain the high mobility of the T-34 and provide it with heavier armour
Vehicle armour
Military vehicles are commonly armoured to withstand the impact of shrapnel, bullets, missiles, or shells, protecting the personnel inside from enemy fire. Such vehicles include tanks, aircraft, and ships....
protection against modern tank guns. In November 1943, the chief designer, A. A. Morozov, presented the overall design of the vehicle and a model of the tank, which received the designation T-44 (Ob'yekt 136). The first prototype was completed by January 1944 and two more were completed in February. The first two prototypes were armed with 85 mm D-5T guns and received the designation T-44-85, while the third prototype was armed with the 122 mm D-25-44T tank gun and received the designation T-44-122. The D-25-44T tank gun was very similar to the basic D-25 field gun, but differed in some minor details including fixed single-piece ammunition to increase the rate of fire and a double-baffle muzzle brake. What allowed fitting such powerful armament in a medium tank weighing 30 tonnes was the construction of the hull with an innovative placement of the engine. Unlike most tanks, in the T-44 the engine was placed perpendicular to the axis of the tank. The hull was designed without sponsons. It was also much wider which made the crew compartment bigger and allowed the turret to be placed over the center part of the vehicle. This reduced the overall length of the vehicle. The thickness of the armour was 75 mm on the front of the hull and 90 mm on the front of the turret. The side armour was 45 mm thick and could be reinforced by 30 mm thick additional armour plate. All three prototypes were powered by the V-2IS diesel engine which developed 500 hp (373 kW). This first generation of prototypes featured a raised cast driver's hatch with an opening vision flap as well as mounting bolts in a ring around the base of the gun tube.
Morozov's new medium tank design received a skeptical response. It was believed that putting a high-speed 12-cylinder engine with a working displacement of almost 40 liters perpendicular to the direction of travel would cause problems, including breaking the connecting rods. It was believed that decreasing the displacement of the engine compartment for the purpose of enlarging the fighting compartment was unnecessary and that moving the turret rearwards would limit the elevation angle of the main gun. However, it turned out that even though rotating the engine complicated the transmission by introducing an additional reduction gear - gear-train and fan drive, it also solved many problems. The cover of the engine and transmission compartment turned along with the radiator; this allowed easier access to the engine, transmission and batteries. The significant decrease in the length of the engine compartment allowed the turret to be moved rearwards, which in turn moved its rotation axis and the center of mass to the center of the hull, increased the accuracy of the main gun and decreased a chance that the turret could get stuck after getting hit in the turret ring with a projectile that ricocheted. The thickness of the frontal armor protection more than doubled without disturbing the center of mass or drastically increasing the weight of the tank. At the beginning of World War II the thickness of T-34 armor was considered enough. Improvements made to the T-34 during World War II included increasing the caliber of the gun (from 76.2 mm to 85 mm) and thickening the armor of the turret. No significant improvements were made to the hull. Increasing the size of the fighting compartment allowed the removal of floor ammunition stowage. The height of the tank was decreased by 300 mm, even though the turret remained almost the same. Removal of the conical pair in the transmission permitted fitting a more compact gear box and improved the control of the brakes and the steering clutch. Visibility from the driver's position was improved. The driver was protected from being splashed by water while the vehicle was fording. The new torsion bar suspension allowed easier crossing of rough ground.
Second generation
Like the T-44-122 prototype, one of the two first-generation T-44-85 prototypes went through competitive trials against the captured German Panzerkampfwagen V Panther medium tank. The second of the two first-generation T-44-85 prototypes was put in competitive trials against the T-44-122 prototype. The second prototype uncovered additional faults in the design. By May 1944 two second-generation prototypes were being built. These featured the driver's position moved rearwards so that his hatch was partially on the hull roof. The driver's vision flap was reduced to a plain square flap with rounded lower corners, in line with the glacis plate. These prototypes had prominent collars at the base of the gun tube, without the mounting bolts which were present in the first generation prototypes. The two prototypes also have differences between each other. One prototype had a splashboard on the glacis plate while the other had a smooth uncluttered glacis plate. One of these prototypes passed trials at the NIBT proving grounds near Kubinka
Kubinka
Kubinka is a town in Odintsovsky District of Moscow Oblast, Russia, located on the Setun River, west of Moscow. Population: Kubinka was the location of the Soviet Union's tank proving grounds, and today is the home of the Kubinka Tank Museum...
in June and July 1944. This prototype weighed 31.3 tonnes and was armed with an 85 mm ZiS-S-53 gun. The turret front armour thickness was increased to 115 mm. Hulls side armour thickness was increased to 75 mm.
T-44A
The third generation prototype, which received the designation T-44A, was completed after the Morozov Design BureauKharkiv Morozov Machine Building Design Bureau
Kharkiv Morozov Machine Building Design Bureau , often simply called Morozov Design Bureau or abbreviated KMDB, is a state-owned company in Kharkiv, Ukraine, which designs armoured vehicles, including the T-80UD and T-84 main battle tanks, as well as military prime movers...
had moved back to Kharkiv
Kharkiv
Kharkiv or Kharkov is the second-largest city in Ukraine.The city was founded in 1654 and was a major centre of Ukrainian culture in the Russian Empire. Kharkiv became the first city in Ukraine where the Ukrainian Soviet Socialist Republic was proclaimed in December 1917 and Soviet government was...
in Ukraine
Ukraine
Ukraine is a country in Eastern Europe. It has an area of 603,628 km², making it the second largest contiguous country on the European continent, after Russia...
. The hull upper front armour (glacis plate) thickness was increased to 90 mm and the turret front armour thickness was increased to 120 mm. Even though it was more heavily armoured, the weight went down to 30.7 tonnes. This vehicle had a new V-44 12-cylinder 4-stroke diesel engine of 520 hp (388 kW) at 1,800 rpm, which allowed the tank to travel at a speed of 60.5 km/h. This prototype had the splashboard on the glacis plate like one of the second generation T-44-85 prototypes. This prototype featured some other differences from the earlier prototypes, including the fact that drivers hatch was moved entirely to the roof of the hull and the vision flap was deleted from the design and replaced by a vision slot in the glacis plate. After trials conducted in August and September 1944 and after it received several upgrades (which increased the weight of the vehicle to 32 tonnes), the T-44A officially entered service with the Red Army on the 23 November 1944.
T-44-100 and T-54
Description
The T-44 had a typical tank layout: the driving compartment at the front, the fighting compartment in the middle and the engine compartment in the rear. The original intention was to retain the high mobility and speed of a T-34 and to provide the T-44 with heavier armourVehicle armour
Military vehicles are commonly armoured to withstand the impact of shrapnel, bullets, missiles, or shells, protecting the personnel inside from enemy fire. Such vehicles include tanks, aircraft, and ships....
protection against large-caliber tank guns. This was accomplished by adding thicker armour but reducing the internal volume of the hull. The T-44 had a lower profile than the T-34, and was potentially simpler to manufacture. Although the T-44 used many components of the T-34, it had a new hull, and a modified model V-2 diesel engine, suspension and transmission.
Reflecting trends in other designs in this period, the T-44 was designed without the hull radio operator/machine gunner position present in many older designs. This was done for a number of reasons. The extensive machine gun firing port in the glacis plate (which was present in T-34 medium tank) was a weak spot in the armour. In the T-34, this firing port and the driver's hatch were exploited during World War II by the Germans fighting the T-34s. Shooting the machine gun was ineffective as it was inaccurate due to obscured vision. It was considered inefficient to transfer reports through an additional member of the crew and therefore these duties were transferred to the commander. The space saved was used for a fuel tank and to increase the ammunition load. The driver's hatch was on the left side of the hull roof. The tank had an improved hull design, longer and wider than the T-34 but slightly lower thanks to the relocation of the air filter, with thicker armour, and was simpler to construct. The hull had a sloped glacis plate, vertical sides, and a slightly beveled rear. Most tanks had a splashboard on the glacis plate although there are pictures of T-44A tanks without them. It protected the upper part of the vehicle from splashes of mud or water. There were three mounts for rectangular stowage bins on the fenders (two on the right fender and one on the left fender). There were four mountings for cylindrical fuel tanks on the fenders (two per side). This was changed in the T-44M which used rectangular fuel cells.
During its service the tank proved to be not entirely adapted to winter conditions as due to an incomplete draining of the cooling system, caused by a water pump system that had been modified to reduce engine height. A small shaft would break after the impeller pump froze. The repair of the shaft, considering the field conditions, proved very impractical and required three people. Two people had to hold a third person by the legs and lower him into the engine bay, where he had to loosen the fastening and remove the broken shaft. Then, he was pulled out and lowered back down to install the new shaft. He was repeatedly lowered until the new part was secured. Another serious problem discovered during the winter conditions was that the crews of the T-44A suffered from frostbite because of the complete lack of a heating system. The driver was supposed to be protected from rain and snow by a removable tarp cover with a small glass window. However, this was not successful and its use was deemed impractical.
The T-44 had a compact torsion-bar suspension instead of the T-34's Christie
Christie suspension
The Christie suspension is a suspension system developed by American engineer Walter Christie for his tank designs. It allowed considerably longer movement than conventional leaf spring systems then in common use, which allowed his tanks to have considerably greater cross-country speed and a lower...
coil springs, although it retained the Christie method of engagement between the slotted drive wheel and track
Caterpillar track
Continuous tracks or caterpillar tracks are a system of vehicle propulsion in which modular metal plates linked into a continuous band are driven by two or more wheels...
lugs. The suspension had five large spoked road wheels and 'dead' 500 mm long track from the T-34. The hull and wheels were virtually identical to the early T-54 main battle tanks although the original T-44 had the T-34's 'spider' road wheels and a narrow, inset drive wheel at the rear. The T-44 was the last Soviet medium tank with paddle-type tracks. The mechanism for tensioning them was significantly better on the T-44 than it was on the T-34. On the T-34, first two lug-nuts on the crank had to be loosened and then the crank pounded with a sledge hammer in order to separate it from the hull. After the track was tensioned, the crank had to be set back in place with a sledge hammer. The whole process required up to three people. On the T-44, the same task could be carried out by one person, without the help of a sledge-hammer. The roadwheels were spaced evenly from each other except for a prominent gap between two of the roadwheels. The T-44-85 and T-44-122 prototypes had a gap between the second and third roadwheels like in the T-34 but the T-44A had a gap between the first and second roadwheels. This arrangement of wheels was continued in the T-54 and T-55 main battle tanks. The roadwheels sometimes started to 'fall home' after 2,500 km. To increase the service life of the road wheel, a slight camber of the paired road wheels was tried. However, this resulted in greater stress on the outer rollers. When the tank crosses 20 km of rough ground it can pick up about a ton of dirt along the way.
The new V-44 12-cylinder 4-stroke diesel engine, developing 520 hp (388 kW) at 1,800 rpm, was a more powerful version of the T-34's model V-2 with a new planetary manual 5-speed transmission system, filtration system, improved cooling system, horizontally placed water and oil pumps and an improved fuel system which increased its power output, although the tank retained the side clutches from the T-34. The new engine gave the T-44 a maximal road speed of 53 km/h and maximal cross country speed of 20 km/h to 25 km/h as well as maximal road range of 350 km. The engine could become worn out after the tank traveled 3,000 km. When that happened, the oil pressure would drop to 2-3 atmospheres and under heavy loads, the engine would start smoking, spewing out black smog out of the side of the tank. The engine deck had two transverse ventilation grilles at the rear. The exhaust port was on the rear left hand side of the hull. The tank could cross 1 m high vertical obstacles, 2.5 m wide trenches, 32° side slopes and 60° gradients and ford 1.3 m deep water obstacles without preparation.
Because driver's hatch was moved from the glacis plate and positioned so that he exited the vehicle perpendicularly instead of crawling out of the hatch, his seat received an elevating mechanism. While in a relatively safe area the driver could elevate his seat to look outside of the tank, providing greater visibility and easier access to the controls. While in combat the driver lowered his seat back into the tank and had to rely on the vision slot protected by triplex (three-layer glass). While in this position the pedals of the main clutch, the fuel supply, and incline brake were positioned much higher and the levers of the steering clutch and gear shifting became inconvenient to operate. Early examples had transmission problems. While the driver was switching gears, two gears could engage simultaneously, which caused a broken gear pinion. This and other gearbox related problems were solved in a 1961 T-44M modernization with the introduction of a gearbox from the T-54 main battle tank.
T-44A was armed with an 85 mm ZiS-S-53 tank gun as well as two 7.62 mm DTM light machine guns. One of these machine guns was mounted to fire through a tiny hole in the center of the glacis plate. Because the tank's crew did not include a radio operator/machine gunner, the driver operated this light machine gun. The gun was mounted in a fixed position and could only be aimed by turning the tank. The main gun was placed in a centrally placed turret along with a coaxially mounted 7.62 mm DTM light machine gun. The ZiS-S-53 tank gun could penetrate around 100 mm of armour at range of 1000 m. The gun could be elevated or depressed between -5° and +25°. It wasn't stabilized. Like in the T-34 and SU-76
SU-76
The SU-76 was a Soviet self-propelled gun used during and after World War II.- History :The SU-76 was based on a lengthened and widened version of the T-70 tank chassis...
SPG
SPG
-Activities:*Submersible pressure gauge used in scuba diving*Shortest proof game, a type of chess problem*Steals per game, a statistic in basketball-Language:...
, hot cartridge-cases were rolling under the feet of the crew. The crew was also subjected to gases from the main gun every time after it was fired. The tank carried 58 rounds for the 85 mm ZiS-S-53 tank gun and 1890 rounds for 7.62 mm DTM light machine guns.
The turret was cast, with a prominent horizontal casting seam, shaped like an elongated hexagon, with sloped sides and overhang all around. It resembled a longer, better armoured T-34-85 turret. It had a cast gun mantlet
Gun mantlet
A gun mantlet is an armour plate or shield attached to an armoured fighting vehicle's gun, protecting the opening through which the weapon's barrel projects from the hull or turret armour and, in many cases, ensuring the vulnerable warhead of a loaded shell does not protrude past the vehicle's...
with a small but prominent ring/collar around the base of the tank gun tube. The turret roof had a raised commander's cupola on the left and loader's hatch on the right with a low dome-shaped ventilator behind it. The turret was moved with an electric motor. The front armour of the turret was 120 mm thick while the side armour was 75 mm thick.
The hull was made of rolled welded steel. The glacis plate was 90 mm thick while the side armour was 75 mm and the bottom armour was 20 mm thick. T-44 tanks could be fitted with additional 30 mm thick armour plates on the sides of the hull and the turret. Additional spaced armour panels could be fitted to the sides of the hull.
The T-44A could be fitted with the PT-3 mine clearing device. It had a radio in the back of the turret with an antenna at the center of the left side of the turret. The vehicle was equipped with a submachine gun. The vehicle lacked an NBC (nuclear, biological and chemical) protection system and a night vision device.
Production history
The T-44A officially entered service with the Red Army on 23 November 1944 but the production started in October. Production took place at the new Factory No. 75 (Zavod 75) in Kharkiv which used the buildings of the old KhPZ Factory No. 183 which were recaptured from Germans on 23 August 1943. To restore the factories to working order, engineers, workers, machines and tools were sent from Stalin Ural Tank Factory No. 183, located in Nizhny Tagil. The original plans were that the factory would produce 300 T-44As a month. However, only 25 were built by the end of 1944. In 1945, 940 were built, making a total of 965 (190 tanks built in 1944 and 1945 were completed by the end of the war). An additional 858 T-44As were made in 1946-1947. The T-34 continued to account for 85% of medium tank production through 1950, and development of a more advanced medium tank with a more powerful 100 mm gun proceeded. The relatively brief production run ended in 1947 with a total of 1,823 T-44A tanks built. The reasons for such a brief production run included mechanical teething problems, the end of the war which reduced the Red Army's need for a new tank, and the design's inability to successfully fit a 100 mm tank gun. It was replaced on the production lines by the T-54-1 main battle tank, which was more mechanically reliable and could mount a 100 mm gun. The superior T-54-2 would replace T-34 production at the Omsk Factory No. 183 in 1950, and the T-54/55 main battle tank series would remain in production until 1981.Service history
The T-44 was issued to three tank brigades mustered on 15 September 1944 for training purposes, but these formations (6th Guards, 33rd Guards, and 63rd Guards Tank Brigades) were re-equipped with T-34-85 tanks prior to entering the Battle of BerlinBattle of Berlin
The Battle of Berlin, designated the Berlin Strategic Offensive Operation by the Soviet Union, was the final major offensive of the European Theatre of World War II....
and Prague Offensive
Prague Offensive
The Prague Offensive was the last major Soviet operation of World War II in Europe. The offensive, and the battle for Prague, was fought on the Eastern Front from 6 May to 11 May 1945. This battle for the city is particularly noteworthy in that it ended after the Third Reich capitulated on 8 May...
. The T-44A was not used operationally during World War II in Europe for several reasons, including the fact that the Red Army was not ready to accept a new tank because of lack of sufficient spares and technical specialists who could repair and maintain the new tanks as well as the fact that many of the tank crews would have to be retrained. However, three tanks were sent to the 100th Special Tank Company which tested them on the Eastern Front
Eastern Front (World War II)
The Eastern Front of World War II was a theatre of World War II between the European Axis powers and co-belligerent Finland against the Soviet Union, Poland, and some other Allies which encompassed Northern, Southern and Eastern Europe from 22 June 1941 to 9 May 1945...
. Many T-44As were immediately sent after they were produced in the Far East regions of the Soviet Union. The first tanks arrived there before the end of the war and were used operationally during the last three days of fighting. They continued to arrive after the war and eventually around 600 T-44As were stationed there.
Due to the Cold War, the USSR decided to keep the tank secret. It was never shown publicly during military parades and pictures were never shown publicly until the secrecy was dropped. There is almost no photographic evidence of T-44s stationed in East Germany or during the Soviet invasion of Hungary in 1956 although it is known that T-44s were sent there (there are only a small number of photos of T-44As in Hungary in existence).
In 1961, a number of T-44As were modernized with parts from the T-54 main battle tank and other upgrades and received the designation T-44M. In 1963, some T-44Ms were converted into T-44MK command tanks. In 1965 some T-44Ms were converted into BTS-4A armoured recovery vehicles. In 1966, a number of T-44As and T-44Ms received the "Cyclone" gun stabilizer and the designations T-44S and T-44MS, respectively. According to most sources T-44S, T-44M and T-44MS tanks remained in service with the Soviet Army until the end of the 1970s, when their usefulness as tanks had ended. It is possible that they remained in storage until the beginning of 1990s. Many T-44Ms were converted into artillery tractors, tank tractors and engineer tanks. A number of T-44A, T-44S, T-44M, T-44MK and T-44MS tanks were converted into fixed defensive positions; some of which are known to have been positioned on the border with the People's Republic of China
People's Republic of China
China , officially the People's Republic of China , is the most populous country in the world, with over 1.3 billion citizens. Located in East Asia, the country covers approximately 9.6 million square kilometres...
. Unlike most Soviet made weapons the T-44 wasn't exported.
After the cloak of secrecy was lifted in 1960s, when the tank was already becoming obsolete, it was used in the war movies: Father of a Soldier, Liberation
Liberation (film series)
Liberation is an epic five-part film series considered the most large-scale World War II film ever made in the Soviet Union. Filmed from 1967 to 1971, the first part was released during 1970 for the 25th anniversary of Victory Day...
, Battle of Moscow
Battle of Moscow (film)
The Battle of Moscow is a 1985 Soviet two-part film, presenting a dramatized account of the 1941 Battle of Moscow and the events preceding it. The films were a Soviet-East German-Czechoslovak-Vietnamese co-production directed by Yuri Ozerov who also wrote the script...
, Red Cherry
Red Cherry
Red Cherry is a 1995 film directed by Ye Ying . The Director of Photography was Zhang Li, a fifth generation filmmaker and classmate of Chen Kaige. Red Cherry won Best Picture at the 1996 Golden Rooster Awards....
, The Star, and Downfall
Downfall (film)
Downfall is a 2004 German/Italian/Austrian epic war film directed by Oliver Hirschbiegel, depicting the final ten days of Adolf Hitler's life in his Berlin bunker and Nazi Germany in 1945....
. In the first, it was used to portray a T-34. In Liberation, Red Cherry, The Star, and Downfall it was visually modified with additional plates to resemble the Tiger I
Tiger I
Tiger I is the common name of a German heavy tank developed in 1942 and used in World War II. The final official German designation was Panzerkampfwagen Tiger Ausf. E, often shortened to Tiger. It was an answer to the unexpectedly formidable Soviet armour encountered in the initial months of...
heavy tank
Heavy tank
A heavy tank was a subset of tank that filled the heavy direct-fire role of many armies.Heavy tanks have usually been deployed to breakthrough enemy lines, though in practice have been more useful in the defensive role than in the attack...
. Some T-44 and T-34 tanks were visually modified to represent German Panzerkampfwagen IVs. They were made for Soviet era film studios and were used in a number of movies about battles on the Eastern Front
Eastern Front (World War II)
The Eastern Front of World War II was a theatre of World War II between the European Axis powers and co-belligerent Finland against the Soviet Union, Poland, and some other Allies which encompassed Northern, Southern and Eastern Europe from 22 June 1941 to 9 May 1945...
. They were also used during a 2004 re-enactment of the Battle of Moscow
Battle of Moscow
The Battle of Moscow is the name given by Soviet historians to two periods of strategically significant fighting on a sector of the Eastern Front during World War II. It took place between October 1941 and January 1942. The Soviet defensive effort frustrated Hitler's attack on Moscow, capital of...
. Some T-44As were given to military museums including one in Brest
Brest, Belarus
Brest , formerly also Brest-on-the-Bug and Brest-Litovsk , is a city in Belarus at the border with Poland opposite the city of Terespol, where the Bug River and Mukhavets rivers meet...
in today's Belarus
Belarus
Belarus , officially the Republic of Belarus, is a landlocked country in Eastern Europe, bordered clockwise by Russia to the northeast, Ukraine to the south, Poland to the west, and Lithuania and Latvia to the northwest. Its capital is Minsk; other major cities include Brest, Grodno , Gomel ,...
. One of two T-44-100 prototypes is in the Kubinka Tank Museum
Kubinka Tank Museum
The Kubinka Tank Museum is a large museum of armoured fighting vehicles in Kubinka, just outside Moscow. It has many famous tanks from World War I, World War II and the Cold War. The museum also houses many unique vehicles, such as the Panzer VIII Maus, Troyanov super-heavy tank and a Karl-Gerät...
.
Combat history
- World War IIWorld War IIWorld War II, or the Second World War , was a global conflict lasting from 1939 to 1945, involving most of the world's nations—including all of the great powers—eventually forming two opposing military alliances: the Allies and the Axis...
– briefly fielded in 1944–45, but kept out of combat - Hungarian Revolution – not known to have seen combat
Variants
- T-44-85 (1944) – Designation for two first generation prototypes armed with 85 mm D-5T tank gun and two second generation prototypes armed with 85 mm ZiS-S-53 tank gun.
- T-44A (1944) – Designation for the third generation prototype and the production model.
- T-44S (1966) – T-44A fitted with "Cyclone" two-plane gun stabilization system.
- T-44M (1961) – T-44A modernization incorporating a drive train upgraded to match the one used in T-54 including the V-54 12-cylinder 38.88 liter water-cooled diesel engine developing 523 hp (390 kW), gearbox, tracks, 'starfish' road wheels and a conventional toothed drive sprocket, flush with the outer track edge. It had an increased ammunition stowage (from 58 rounds to 61 rounds), new R-113 and R-120 radio sets, a heater and infra-red night sight, TVN-2 night vision device for the driver as well as another fuel tank which increased the fuel capacity by 150 liters to 650 liters and 800 liters with additional fuel tanks. The maximal road operational range of the tank increased to 420 km - 440 km. The original fenders were replaced with T-54-style ones. The catwalk stowage was changed to the flat T-54 rectangular external fuel tanks with embossed circle and cross. Hence the T-44M had a different arrangement of additional fuel tanks and stowage boxes. There were four rectangular external fuel tanks as well as two smaller ones on the right fender and fastenings for four spare track chain links, one rectangular external fuel tank as well as two smaller ones and one stowage box. The tank received a mount for an antiaircraft machine gun. A T-54-style headlight cluster with two headlights was added to right hand side of the glacis plate and the T-34-style headlight on the left hand side of the hull was removed.
- T-44MK (1963) – T-44M converted into a command tank. Apart from standard T-44M equipment, it is equipped with R-112 radio set. The ammunition stowage was reduced by 15 rounds to 46 rounds.
- T-44MS (1966) - T-44M fitted with "Cyclone" two-plane gun stabilization system. It also has increased maximal operational range.
- BTS-4A (1965) – T-44M converted into an armoured recovery vehicleArmoured recovery vehicleAn armoured recovery vehicle is a type of armoured fighting vehicle used to repair battle- or mine-damaged as well as broken-down armoured vehicles during combat, or to tow them out of the danger zone for more extensive repairs...
. The turret has been removed. The vehicle was fitted with a stowage basket, a hoist and a small folding crane with a capacity of 3 tonnes and a snorkel. It was also known as BTS-4-44M.
- T-44A (1944) – Designation for the third generation prototype and the production model.
- T-44 tanks converted into fixed fortifications. This process usually involved the removal of the engine and the gearbox while burying the tank up to the top of the hull and covering the turret in concrete to break up the outline and to give it a rock-like appearance.
- T-44-122 (1944) – First generation prototype armed with D-25-44T 122 mm tank gun. It carried 24 rounds.
- T-44-100 (1945) – Prototype fitted with a new modified turret which would allow fitting the 100 mm D-10T gun or 100 mm LB-1 gun. The tank carries 36 rounds for the 100 mm tank gun. This prototype had the 12.7 mm DShK anti-aircraft heavy machine gun fitted to the loader's hatch, 6 mm thick sideskirts protecting the sides and two cylindrical fuel tanks in the back giving it a fuel capacity of 1035L. The longer tank gun barrel increased the overall length of the vehicle to 8.04 m. The new turret, new armament and the sideskirts made the vehicle heavier as it weighed 34.55 tonnes.
External links
- T-44 Medium Tank at battlefield.ru
- T-44 Medium Tank at wwiivehicles.com
- Rem Ulanov: The Transitional Variant, memoir of a T-44 test driver, at battlefield.ru