White clipper
Encyclopedia
White clipper is a circuit in professional video products that limits the maximum amplitude of the luminance part of the analogue video signal to 1 volt. It is essential for both analogue recording or transmission of video material.
For transmission, this signal modulates the amplitude of the carrier. The modulation index is negative , i.e., higher video level yields lower carrier (RF) level and vice versa. 1 volt (white) video yields only 10 % of the full carrier level. In a later stage, aural signal is superimposed on this signal. For transmission, this signal modulates the amplitude of the carrier.
If by any reason, the video signal increases beyond 1 volt, the portion of video in excess of 1 volt begins to interfere with the aural signal. The repetition rate of a line is about 15 kHz. ( 15625 in system B and 15750 in system M) The repetition rate of a field is 50 or 60 Hz. (50 in system B and 60 in system M) So the interference has two components; a very high pitched sound of 15 kHz and a low pitched sound of 50 Hz (or 60 Hz.) On the other hand video input in excess of 1.1 volt results in the loss of the carrier level and this tends to shut down the transmitter.
For this reason a white clipper circuit is used to strictly limit the maximum amplitude of the video waveform at the transmitter.
signal (a subcarrier modulated by the color information) is superimposed on the monochrome signal (luminance). In a studio environment the total video level while showing a color at maximum saturation (such as yellow) may exceed 1 V. But for transmission maximum amplitude is limited by the use of the various matrix values in the encoder - PAL or NTSC.
clips out the signal in excess of 1 volt. In the second arm, chrominance signal bypasses the Zener diode via a band pass filter.Sometimes it is necessary or desirable to create a soft clipping action where some highlight detail can be preserved in high contrast scenes. This is known as "knee" circuit after the transfer characteristic graph.
Video signal
The standard video signal (or more precisely composite video signal ) is a signal with a maximum level of 1 volt into 75 Ω. In this signal 0.3 volt corresponds to black and 1 volt corresponds to white. Video circuits are designed around these limits. These limits apply to recording on analogue video tape and analogue transmission as well as in analogue to digital video converters.For transmission, this signal modulates the amplitude of the carrier. The modulation index is negative , i.e., higher video level yields lower carrier (RF) level and vice versa. 1 volt (white) video yields only 10 % of the full carrier level. In a later stage, aural signal is superimposed on this signal. For transmission, this signal modulates the amplitude of the carrier.
If by any reason, the video signal increases beyond 1 volt, the portion of video in excess of 1 volt begins to interfere with the aural signal. The repetition rate of a line is about 15 kHz. ( 15625 in system B and 15750 in system M) The repetition rate of a field is 50 or 60 Hz. (50 in system B and 60 in system M) So the interference has two components; a very high pitched sound of 15 kHz and a low pitched sound of 50 Hz (or 60 Hz.) On the other hand video input in excess of 1.1 volt results in the loss of the carrier level and this tends to shut down the transmitter.
For this reason a white clipper circuit is used to strictly limit the maximum amplitude of the video waveform at the transmitter.
Chrominance
Color TV signal is almost the same as monochrome signal, except that the chrominanceChrominance
Chrominance is the signal used in video systems to convey the color information of the picture, separately from the accompanying luma signal . Chrominance is usually represented as two color-difference components: U = B' − Y' and V = R' − Y'...
signal (a subcarrier modulated by the color information) is superimposed on the monochrome signal (luminance). In a studio environment the total video level while showing a color at maximum saturation (such as yellow) may exceed 1 V. But for transmission maximum amplitude is limited by the use of the various matrix values in the encoder - PAL or NTSC.
The circuit
The white clipper is a circuit which clips out the excess level of video signal. It is especially important for those transmitters which receive the signals by professional receivers from other transmitters. The circuit has two parallel arms. In the first arm a Zener diodeZener diode
A Zener diode is a special kind of diode which allows current to flow in the forward direction in the same manner as an ideal diode, but will also permit it to flow in the reverse direction when the voltage is above a certain value known as the breakdown voltage, "Zener knee voltage" or "Zener...
clips out the signal in excess of 1 volt. In the second arm, chrominance signal bypasses the Zener diode via a band pass filter.Sometimes it is necessary or desirable to create a soft clipping action where some highlight detail can be preserved in high contrast scenes. This is known as "knee" circuit after the transfer characteristic graph.