Heat detector
Encyclopedia
A heat detector is a fire alarm device designed to respond when the convected thermal energy of a fire increases the temperature of a heat sensitive element.
The thermal mass and conductivity of the element regulate the rate flow of heat into the element. All heat detectors have this thermal lag
. Heat detectors have two main classifications of operation, "rate-of-rise" and "fixed temperature."
reaches the eutectic point changing state from a solid to a liquid. Thermal lag
delays the accumulation of heat at the sensitive element so that a fixed-temperature device will reach its operating temperature sometime after the surrounding air temperature exceeds that temperature. The most common fixed temperature point for electrically connected heat detectors is 136.4°F (58°C). Technological developments have enabled the perfection of detectors that activate at a temperature of 117°F (47°C), increasing the available reaction time and margin of safety. This type of technology has been available for decades without the use of batteries or electricity as shown in the picture.
Rate of rise detectors may not respond to low energy release rates of slowly developing fires. To detect slowly developing fires combination detectors add a fixed temperature element that will ultimately respond when the fixed temperature element reaches the design threshold.
Mechanical heat detectors are independent fire warning stations that - unlike smoke detectors - can be installed in any area of a home. Portability, ease of installation, and excellent performance and reliability make this a good choice for residential fire protection when combined with the required smoke detectors. Because the detectors are not interconnected, heat activation identifies the location of the fire, facilitating evacuation from the home.
Each type of heat detector has its advantages, and it cannot be said that one type of heat detector should always be used instead of another. If you were to place a rate-of-rise heat detector above a large, closed oven, then every time the door is opened a nuisance alarm could be generated due to the sudden heat transient. In this circumstance the fixed threshold detector would probably be best. If a room filled with highly combustible materials is protected with a fixed heat detector then a fast-flaming fire could exceed the alarm threshold due to thermal lag. In that case the rate-of-rise heat detector may be preferred.
The thermal mass and conductivity of the element regulate the rate flow of heat into the element. All heat detectors have this thermal lag
Thermal lag
"'Thermal lag'" describes a material's thermal mass with respect to time. A material with high thermal mass will have a large thermal lag....
. Heat detectors have two main classifications of operation, "rate-of-rise" and "fixed temperature."
Fixed temperature heat detectors
This is the most common type of heat detector. Fixed temperature detectors operate when the heat sensitive eutectic alloyEutectic system
A eutectic system is a mixture of chemical compounds or elements that has a single chemical composition that solidifies at a lower temperature than any other composition. This composition is known as the eutectic composition and the temperature is known as the eutectic temperature...
reaches the eutectic point changing state from a solid to a liquid. Thermal lag
Thermal lag
"'Thermal lag'" describes a material's thermal mass with respect to time. A material with high thermal mass will have a large thermal lag....
delays the accumulation of heat at the sensitive element so that a fixed-temperature device will reach its operating temperature sometime after the surrounding air temperature exceeds that temperature. The most common fixed temperature point for electrically connected heat detectors is 136.4°F (58°C). Technological developments have enabled the perfection of detectors that activate at a temperature of 117°F (47°C), increasing the available reaction time and margin of safety. This type of technology has been available for decades without the use of batteries or electricity as shown in the picture.
Rate-of-rise heat detectors
Rate-of-Rise (ROR) heat detectors operate on a rapid rise in element temperature of 12° to 15°F (6.7° to 8.3°C) increase per minute, irrespective of the starting temperature. This type of heat detector can operate at a lower temperature fire condition than would be possible if the threshold were fixed. It has two heat-sensitive thermocouples/ thermistor. One thermocouple monitors heat transferred by convection or radiation. The other responds to ambient temperature. Detector responds when first’s temperature increases relative to the other.Rate of rise detectors may not respond to low energy release rates of slowly developing fires. To detect slowly developing fires combination detectors add a fixed temperature element that will ultimately respond when the fixed temperature element reaches the design threshold.
Heat detector selection
Heat detectors commonly have a label on them that says "Not a life safety device". That is because heat detectors are not meant to replace smoke detectors in the bedrooms or in the hallway outside of the bedrooms. A heat detector will nonetheless notify of a fire in a kitchen or utility area (i.e., laundry room, garage, or attic), where smoke detectors should not be installed. This will allow extra time to evacuate the building or to put out the fire if possible.Mechanical heat detectors are independent fire warning stations that - unlike smoke detectors - can be installed in any area of a home. Portability, ease of installation, and excellent performance and reliability make this a good choice for residential fire protection when combined with the required smoke detectors. Because the detectors are not interconnected, heat activation identifies the location of the fire, facilitating evacuation from the home.
Each type of heat detector has its advantages, and it cannot be said that one type of heat detector should always be used instead of another. If you were to place a rate-of-rise heat detector above a large, closed oven, then every time the door is opened a nuisance alarm could be generated due to the sudden heat transient. In this circumstance the fixed threshold detector would probably be best. If a room filled with highly combustible materials is protected with a fixed heat detector then a fast-flaming fire could exceed the alarm threshold due to thermal lag. In that case the rate-of-rise heat detector may be preferred.
See also
- Fire alarm
- Flame detectorFlame detectorThere are several types of flame detector. The optical flame detector is a detector that uses optical sensors to detect flames. There are also ionisation flame detectors, which use current flow in the flame to detect flame presence, and thermocouple flame detectors.-Ultraviolet:Ultraviolet ...
- Aspirated smoke detectorAspirated smoke detectorAn aspirating smoke detector , consists of a central detection unit which draws air through a network of pipes to detect smoke. The sampling chamber is based on a nephelometer that is capable of detecting the presence of smoke particles suspended in air by detecting the light scattered by them in...
- Smoke detectorSmoke detectorA smoke detector is a device that detects smoke, typically as an indicator of fire. Commercial, industrial, and mass residential devices issue a signal to a fire alarm system, while household detectors, known as smoke alarms, generally issue a local audible and/or visual alarm from the detector...
- Carbon monoxide detectorCarbon monoxide detectorA carbon monoxide detector or CO detector is a device that detects the presence of the carbon monoxide gas in order to prevent carbon monoxide poisoning. CO is a colorless and odorless compound produced by incomplete combustion. It is often referred to as the "silent killer" because it is...
- Passive infrared sensor
- Manual call point or Break glass alarm
- Fire sprinklerFire sprinklerA fire sprinkler system is an active fire protection measure, consisting of a water supply system, providing adequate pressure and flowrate to a water distribution piping system, onto which fire sprinklers are connected...
- Gaseous fire suppressionGaseous fire suppressionGaseous fire suppression is a term to describe the use of inert gases and chemical agents to extinguish a fire. Also called Clean Agent Fire Suppression. These Agents are governed by the NFPA Standard for Clean Agent Fire Extinguishing Systems - NFPA 2001 in the USA, with different standards and...
- Automatic fire suppressionAutomatic fire suppressionAutomatic fire suppression systems control and extinguish fires without human intervention.According to the National Fire Protection Association, there were 1,602,000 fires reported in the United States in 2005. There were 3,675 civilian deaths, 17,925 civilian injuries, and $9.2 billion in...