Radar signal characteristics
Encyclopedia
A radar system
uses a radio frequency
electromagnetic signal
reflected from a target to determine information about that target. In any radar system, the signal transmitted and received will exhibit many of the characteristics described below.
to allow the system to capture the required data. In simple ranging radars, the carrier will be pulse modulated and in continuous wave
systems, such as Doppler radar
, modulation may not be required. Most systems use pulse modulation, with or without other supplementary modulating signals. Note that with pulse modulation, the carrier is simply switched on and off in sync with the pulses; the modulating waveform does not actually exist in the transmitted signal and the envelope of the pulse waveform is extracted from the demodulated carrier in the receiver. Although obvious when described, this point is often missed when pulse transmissions are first studied, leading to misunderstandings about the nature of the signal.
) (or pulse duration) of the transmitted signal is to ensure that the radar emits sufficient energy to allow that the reflected pulse is detectable by its receiver. The amount of energy that can be delivered to a distant target is the product of two things; the output power of the transmitter, and the duration of the transmission. Therefore pulse width constrains the maximum detection range of a target.
It also determines the range discrimination, that is the capacity of the radar to distinguish between two targets fairly close together. At any range, with similar azimuth and elevation angles and as viewed by a radar with an unmodulated pulse, the range discrimination is approximately equal in distance to half of the pulse duration.
Pulse width also determines the dead zone at close ranges. While the radar transmitter is active, the receiver input is blanked to avoid the amplifiers being swamped (saturated) or, (more likely), damaged. A simple calculation reveals that a radar echo will take approximately 10.8 μs to return from a target 1 standard mile away (counting from the leading edge of the transmitter pulse (T0), (sometimes known as transmitter main bang)). For convenience, these figures may also be expressed as 1 nautical mile in 12.4 μs or 1 kilometre in 6.7 μs. (For simplicity, all further discussion will use metric figures.) If the radar pulse width is 1 μs, then there can be no detection of targets closer than about 150 m, because the receiver is blanked.
All this means that the designer cannot simply increase the pulse width to get greater range without having an impact on other performance factors. As with everything else in a radar system, compromises have to be made to a radar system's design to provide the optimal performance for its role.
There are two other facets related to PRF that the designer must weigh very carefully; the beamwidth characteristics of the antenna, and the required periodicity with which the radar must sweep the field of view. A radar with a 1° horizontal beamwidth that sweeps the entire 360° horizon every 2 seconds with a PRF of 1080 Hz will radiate 3 pulses over each 1-degree arc. If the receiver needs at least 6 reflected pulses of similar amplitudes to achieve an acceptable probability of detection, then there are three choices for the designer: double the PRF, halve the sweep speed, or double the beamwidth. In reality, all three choices are used, to varying extents; radar design is all about compromises between conflicting pressures.
Without staggered PRF, any pulses originating from another radar on the same radio frequency might appear stable in time and could be mistaken for reflections from the radar's own transmission. With staggered PRF the radar’s own targets appear stable in range in relation to the transmit pulse, whilst the 'jamming' echoes may move around in apparent range (uncorrelated), causing them to be rejected by the receiver. Staggered PRF is only one of several similar techniques used for this, including jittered PRF (where the pulse timing is varied in a less-predictable manner), pulse-frequency modulation, and several other similar techniques whose principal purpose is to reduce the probability of unintentional synchronicity. These techniques are in widespread use in marine safety and navigation radars, by far the most numerous radars on planet Earth today.
Clutter is used by the military to jam radars by the use chaff
. Chaff is small reflective material used to hide troop, ship, or aircraft movements by creating many returns and overwhelming the radar's receiver with spurious targets.
is used to avoid saturation of the receiver from close in ground clutter by adjusting the attenuation of the receiver as a function of distance. More attenuation is applied to returns close in and is reduced as the range increases.
In simple systems, echoes from targets must be detected and processed before the next transmitter pulse is generated if range ambiguity is to be avoided. Range ambiguity occurs when the time taken for an echo to return from a target is greater than the pulse repetition period (T); if the interval between transmitted pulses is 1000 microseconds, and the return-time of a pulse from a distant target is 1200 microseconds, the apparent distance of the target is only 200 microseconds. In sum, these 'second echoes' appear on the display to be targets closer than they really are.
Consider the following example : if the radar antenna is located at around 15 m above sea level, then the distance to the horizon is pretty close, (perhaps 15 km). Ground targets further than this range cannot be detected, so the PRF can be quite high; a radar with a PRF of 7.5 kHz will return ambiguous echoes from targets at about 20 km, or over the horizon. If however, the PRF was doubled to 15 kHz, then the ambiguous range is reduced to 10 km and targets beyond this range would only appear on the display after the transmitter has emitted another pulse. A target at 12 km would appear to be 2 km away, although the strength of the echo might be much lower than that from a genuine target at 2 km.
The maximum non ambiguous range varies inversely with PRF and is given by:
If a longer unambiguous range is required with this simple system, then lower PRFs are required and it was quite common for early search radars to have PRFs as low as a few hundred Hz, giving an unambiguous range out to well in excess of 150 km. However, lower PRFs introduce other problems, including poorer target painting and velocity ambiguity in Pulse-Doppler systems (see below).
Multiple PRF
Modern radars, especially air-to-air combat radars in military aircraft, may use PRFs in the tens-to-hundreds of kilohertz and stagger the interval between pulses to allow the correct range to be determined. With this form of staggered PRF, a packet of pulses is transmitted with a fixed interval between each pulse, and then another packet is transmitted with a slightly different interval. Target reflections appear at different ranges for each packet; these differences are accumulated and then simple arithmetical techniques may be applied to determine true range. Such radars may use repetitive patterns of packets, or more adaptable packets that respond to apparent target behaviors. Regardless, radars that employ the technique are universally coherent, with a very stable radio frequency, and the pulse packets may also be used to make measurements of the Doppler shift (a velocity-dependent modification of the apparent radio frequency), especially when the PRFs are in the hundreds-of-kilohertz range. Radars exploiting Doppler effects in this manner typically determine relative velocity first, from the Doppler effect, and then use other techniques to derive target distance.
Maximum Unambiguous Range
At its most simplistic, MUR (Maximum Unambiguous Range) for a Pulse Stagger sequence may be calculated using the TSP (Total Sequence Period). TSP is defined as the total time it takes for the Pulsed pattern to repeat. This can be found by the addition of all the elements in the stagger sequence. The formula is derived from the speed of light and the length of the sequence :
where c is the speed of light
, usually in metres per microsecond, and TSP is the addition of all the positions of the stagger sequence, usually in microseconds. However, it should be noted that in a stagger sequence, some intervals may be repeated several times; when this occurs, it is more appropriate to consider TSP as the addition of all the unique intervals in the sequence.
Also, it is worth remembering that there may be vast differences between the MUR and the maximum range (the range beyond which reflections will probably be too weak to be detected), and that the maximum instrumented range may be much shorter than either of these. A civil marine radar, for instance, may have user-selectable maximum instrumented display ranges of 72, or 96 or rarely 120 nautical miles, in accordance with international law, but maximum unambiguous ranges of over 40,000 nautical miles and maximum detection ranges of perhaps 150 nautical miles. When such huge disparities are noted, it reveals that the primary purpose of staggered PRF is to reduce "jamming", rather than to increase unambiguous range capabilities.
schemes used in communications systems, such as Frequency Modulation
and consist of the carrier plus a relatively small number of sidebands. When the radar signal is modulated with a pulse train as shown above, the spectrum becomes much more complicated and far more difficult to visualise.
Basic Fourier analysis shows that any repetitive complex signal consists of a number of harmonically related sine waves. The radar pulse train is a form of square wave
, the pure form of which consists of the fundamental plus all of the odd harmonics. The exact composition of the pulse train will depend on the pulse width and PRF, but mathematical analysis can be used to calculate all of the frequencies in the spectrum. When the pulse train is used to modulate a radar carrier, the typical spectrum shown on the left will be obtained.
Examination of this spectral response shows that it contains two basic structures. The Coarse Structure; (the peaks or 'lobes' in the diagram on the left) and the Fine Structure which contains the individual frequency components as shown below. The Envelope of the lobes in the Coarse Structure is given by:
.
Note that the pulse width (
) appears on the bottom of this equation and determines the lobe spacing. Smaller pulse widths result in wider lobes and therefore greater bandwidth.
Examination of the spectral response in finer detail, as shown on the right, shows that the Fine Structure contains individual lines or spot frequencies. The formula for the fine structure is given by 
and since the period of the PRF (T) appears at the top of the fine spectrum equation, there will be fewer lines if higher PRFs are used. These facts affect the decisions made by radar designers when considering the trade-offs that need to be made when trying to overcome the ambiguities that affect radar signals.
Recent advances in signal processing techniques have made the use of pulse profiling or shaping more common. By shaping the pulse envelope before it is applied to the transmitting device, say to a cosine law or a trapezoid, the bandwidth can be limited at source, with less reliance on filtering. When this technique is combined with pulse compression
, then a good compromise between efficiency, performance and range resolution can be realised. The diagram on the left shows the effect on the spectrum if a trapezoid pulse profile is adopted. It can be seen that the energy in the sidebands is significantly reduced compared to the main lobe and the amplitude of the main lobe is increased.
Similarly, the use of a cosine pulse profile has an even more marked effect, with the amplitude of the sidelobes practically becoming negligible. The main lobe is again increased in amplitude and the sidelobes correspondingly reduced, giving a significant improvement in performance.
There are many other profiles that can be adopted to optimise the performance of the system, but cosine and trapezoid profiles generally provide a good compromise between efficiency and resolution and so tend to be used most frequently.
This is an issue only with a particular type of system; the Pulse-Doppler radar
, which uses the Doppler effect
to resolve velocity from the apparent change in frequency caused by targets that have net radial velocities compared to the radar device. Examination of the spectrum generated by a pulsed transmitter, shown above, reveals that each of the sidebands, (both coarse and fine), will be subject to the Doppler effect, another good reason to limit bandwidth and spectral complexity by pulse profiling.
Consider the positive shift caused by the closing target in the diagram which has been highly simplified for clarity.
It can be seen that as the relative velocity increases, a point will be reached where the spectral lines that constitute the echoes are hidden or aliased
by the next sideband of the modulated carrier.
Transmission of multiple pulse-packets with different PRF-values, e.g. staggered PRFs, will resolve this ambiguity, since each new PRF value will result in a new sideband position, revealing the velocity to the receiver. The maximum unambiguous target velocity is given by:
Radar
Radar is an object-detection system which uses radio waves to determine the range, altitude, direction, or speed of objects. It can be used to detect aircraft, ships, spacecraft, guided missiles, motor vehicles, weather formations, and terrain. The radar dish or antenna transmits pulses of radio...
uses a radio frequency
Radio frequency
Radio frequency is a rate of oscillation in the range of about 3 kHz to 300 GHz, which corresponds to the frequency of radio waves, and the alternating currents which carry radio signals...
electromagnetic signal
Electromagnetic radiation
Electromagnetic radiation is a form of energy that exhibits wave-like behavior as it travels through space...
reflected from a target to determine information about that target. In any radar system, the signal transmitted and received will exhibit many of the characteristics described below.
The radar signal in the time domain
The diagram below shows the characteristics of the transmitted signal in the time domain. Note that in this and in all the diagrams within this article, the x axis is exaggerated to make the explanation clearer.Carrier
The carrier is an RF signal, typically of microwave frequencies, which is usually (but not always) modulatedModulation
In electronics and telecommunications, modulation is the process of varying one or more properties of a high-frequency periodic waveform, called the carrier signal, with a modulating signal which typically contains information to be transmitted...
to allow the system to capture the required data. In simple ranging radars, the carrier will be pulse modulated and in continuous wave
Continuous wave
A continuous wave or continuous waveform is an electromagnetic wave of constant amplitude and frequency; and in mathematical analysis, of infinite duration. Continuous wave is also the name given to an early method of radio transmission, in which a carrier wave is switched on and off...
systems, such as Doppler radar
Doppler radar
A Doppler radar is a specialized radar that makes use of the Doppler effect to produce velocity data about objects at a distance. It does this by beaming a microwave signal towards a desired target and listening for its reflection, then analyzing how the frequency of the returned signal has been...
, modulation may not be required. Most systems use pulse modulation, with or without other supplementary modulating signals. Note that with pulse modulation, the carrier is simply switched on and off in sync with the pulses; the modulating waveform does not actually exist in the transmitted signal and the envelope of the pulse waveform is extracted from the demodulated carrier in the receiver. Although obvious when described, this point is often missed when pulse transmissions are first studied, leading to misunderstandings about the nature of the signal.
Pulse width
The pulse width () (or pulse duration) of the transmitted signal is to ensure that the radar emits sufficient energy to allow that the reflected pulse is detectable by its receiver. The amount of energy that can be delivered to a distant target is the product of two things; the output power of the transmitter, and the duration of the transmission. Therefore pulse width constrains the maximum detection range of a target.It also determines the range discrimination, that is the capacity of the radar to distinguish between two targets fairly close together. At any range, with similar azimuth and elevation angles and as viewed by a radar with an unmodulated pulse, the range discrimination is approximately equal in distance to half of the pulse duration.
All this means that the designer cannot simply increase the pulse width to get greater range without having an impact on other performance factors. As with everything else in a radar system, compromises have to be made to a radar system's design to provide the optimal performance for its role.
Pulse repetition frequency (PRF)
In order to build up a discernible echo, most radar systems emit pulses continuously and the repetition rate of these pulses is determined by the role of the system. An echo from a target will therefore be 'painted' on the display or integrated within the signal processor every time a new pulse is transmitted, reinforcing the return and making detection easier. The higher the PRF that is used, then the more the target is painted. However with the higher PRF the range that the radar can "see" is reduced. Radar designers try to use the highest PRF possible commensurate with the other factors that constrain it, as described below.There are two other facets related to PRF that the designer must weigh very carefully; the beamwidth characteristics of the antenna, and the required periodicity with which the radar must sweep the field of view. A radar with a 1° horizontal beamwidth that sweeps the entire 360° horizon every 2 seconds with a PRF of 1080 Hz will radiate 3 pulses over each 1-degree arc. If the receiver needs at least 6 reflected pulses of similar amplitudes to achieve an acceptable probability of detection, then there are three choices for the designer: double the PRF, halve the sweep speed, or double the beamwidth. In reality, all three choices are used, to varying extents; radar design is all about compromises between conflicting pressures.
Staggered PRF
Staggered PRF is a transmission process where the time between interrogations from radar changes slightly, in a patterned and readily-discernible repeating manner. The change of repetition frequency allows the radar, on a pulse-to-pulse basis, to differentiate between returns from its own transmissions and returns from other radar systems with the same PRF and a similar radio frequency. Consider a radar with a constant interval between pulses; target reflections appear at a relatively constant range related to the flight-time of the pulse. In today's very crowded radio spectrum, there may be many other pulses detected by the receiver, either directly from the transmitter or as reflections from elsewhere. Because their apparent "distance" is defined by measuring their time relative to the last pulse transmitted by "our" radar, these "jamming" pulses could appear at any apparent distance. When the PRF of the "jamming" radar is very similar to "our" radar, those apparent distances may be very slow-changing, just like real targets. By using stagger, a radar designer can force the "jamming" to jump around erratically in apparent range, inhibiting integration and reducing or even suppressing its impact on true target detection.Without staggered PRF, any pulses originating from another radar on the same radio frequency might appear stable in time and could be mistaken for reflections from the radar's own transmission. With staggered PRF the radar’s own targets appear stable in range in relation to the transmit pulse, whilst the 'jamming' echoes may move around in apparent range (uncorrelated), causing them to be rejected by the receiver. Staggered PRF is only one of several similar techniques used for this, including jittered PRF (where the pulse timing is varied in a less-predictable manner), pulse-frequency modulation, and several other similar techniques whose principal purpose is to reduce the probability of unintentional synchronicity. These techniques are in widespread use in marine safety and navigation radars, by far the most numerous radars on planet Earth today.
Clutter
Clutter (also termed ground clutter) is a form of radar signal contamination. It occurs when fixed objects close to the transmitter—such as buildings, trees, or terrain (hills, ocean swells and waves)—obstruct a radar beam and produce echoes. The echoes resulting from ground clutter may be large in both areal size and intensity. The effects of ground clutter fall off as range increases usually due to the curvature of the earth and the tilt of the antenna above the horizon. Without special processing techniques, targets can be lost in returns from terrain on land or waves at sea.Clutter is used by the military to jam radars by the use chaff
Chaff (radar countermeasure)
Chaff, originally called Window by the British, and Düppel by the Second World War era German Luftwaffe , is a radar countermeasure in which aircraft or other targets spread a cloud of small, thin pieces of aluminium, metallized glass fibre or plastic, which either appears as a cluster of secondary...
. Chaff is small reflective material used to hide troop, ship, or aircraft movements by creating many returns and overwhelming the radar's receiver with spurious targets.
Sensitivity time control (STC)
STCSensitivity Time Control
Sensitivity Time Control is used to attenuate the very strong signals returned from nearby ground clutter targets in the first few range gates of a Radar receiver. Without this signal attenuation, the receiver would routinely saturate due to the strong signals....
is used to avoid saturation of the receiver from close in ground clutter by adjusting the attenuation of the receiver as a function of distance. More attenuation is applied to returns close in and is reduced as the range increases.
Unambiguous range
Single PRFConsider the following example : if the radar antenna is located at around 15 m above sea level, then the distance to the horizon is pretty close, (perhaps 15 km). Ground targets further than this range cannot be detected, so the PRF can be quite high; a radar with a PRF of 7.5 kHz will return ambiguous echoes from targets at about 20 km, or over the horizon. If however, the PRF was doubled to 15 kHz, then the ambiguous range is reduced to 10 km and targets beyond this range would only appear on the display after the transmitter has emitted another pulse. A target at 12 km would appear to be 2 km away, although the strength of the echo might be much lower than that from a genuine target at 2 km.
The maximum non ambiguous range varies inversely with PRF and is given by:
If a longer unambiguous range is required with this simple system, then lower PRFs are required and it was quite common for early search radars to have PRFs as low as a few hundred Hz, giving an unambiguous range out to well in excess of 150 km. However, lower PRFs introduce other problems, including poorer target painting and velocity ambiguity in Pulse-Doppler systems (see below).
Multiple PRF
Modern radars, especially air-to-air combat radars in military aircraft, may use PRFs in the tens-to-hundreds of kilohertz and stagger the interval between pulses to allow the correct range to be determined. With this form of staggered PRF, a packet of pulses is transmitted with a fixed interval between each pulse, and then another packet is transmitted with a slightly different interval. Target reflections appear at different ranges for each packet; these differences are accumulated and then simple arithmetical techniques may be applied to determine true range. Such radars may use repetitive patterns of packets, or more adaptable packets that respond to apparent target behaviors. Regardless, radars that employ the technique are universally coherent, with a very stable radio frequency, and the pulse packets may also be used to make measurements of the Doppler shift (a velocity-dependent modification of the apparent radio frequency), especially when the PRFs are in the hundreds-of-kilohertz range. Radars exploiting Doppler effects in this manner typically determine relative velocity first, from the Doppler effect, and then use other techniques to derive target distance.
Maximum Unambiguous Range
At its most simplistic, MUR (Maximum Unambiguous Range) for a Pulse Stagger sequence may be calculated using the TSP (Total Sequence Period). TSP is defined as the total time it takes for the Pulsed pattern to repeat. This can be found by the addition of all the elements in the stagger sequence. The formula is derived from the speed of light and the length of the sequence :
where c is the speed of light
Speed of light
The speed of light in vacuum, usually denoted by c, is a physical constant important in many areas of physics. Its value is 299,792,458 metres per second, a figure that is exact since the length of the metre is defined from this constant and the international standard for time...
, usually in metres per microsecond, and TSP is the addition of all the positions of the stagger sequence, usually in microseconds. However, it should be noted that in a stagger sequence, some intervals may be repeated several times; when this occurs, it is more appropriate to consider TSP as the addition of all the unique intervals in the sequence.
Also, it is worth remembering that there may be vast differences between the MUR and the maximum range (the range beyond which reflections will probably be too weak to be detected), and that the maximum instrumented range may be much shorter than either of these. A civil marine radar, for instance, may have user-selectable maximum instrumented display ranges of 72, or 96 or rarely 120 nautical miles, in accordance with international law, but maximum unambiguous ranges of over 40,000 nautical miles and maximum detection ranges of perhaps 150 nautical miles. When such huge disparities are noted, it reveals that the primary purpose of staggered PRF is to reduce "jamming", rather than to increase unambiguous range capabilities.
The radar signal in the frequency domain
Pure CW radars appear as a single line on a Spectrum analyser display and when modulated with other sinusoidal signals, the spectrum differs little from that obtained with standard analogue modulationModulation
In electronics and telecommunications, modulation is the process of varying one or more properties of a high-frequency periodic waveform, called the carrier signal, with a modulating signal which typically contains information to be transmitted...
schemes used in communications systems, such as Frequency Modulation
Frequency modulation
In telecommunications and signal processing, frequency modulation conveys information over a carrier wave by varying its instantaneous frequency. This contrasts with amplitude modulation, in which the amplitude of the carrier is varied while its frequency remains constant...
and consist of the carrier plus a relatively small number of sidebands. When the radar signal is modulated with a pulse train as shown above, the spectrum becomes much more complicated and far more difficult to visualise.
Square wave
A square wave is a kind of non-sinusoidal waveform, most typically encountered in electronics and signal processing. An ideal square wave alternates regularly and instantaneously between two levels...
, the pure form of which consists of the fundamental plus all of the odd harmonics. The exact composition of the pulse train will depend on the pulse width and PRF, but mathematical analysis can be used to calculate all of the frequencies in the spectrum. When the pulse train is used to modulate a radar carrier, the typical spectrum shown on the left will be obtained.
Examination of this spectral response shows that it contains two basic structures. The Coarse Structure; (the peaks or 'lobes' in the diagram on the left) and the Fine Structure which contains the individual frequency components as shown below. The Envelope of the lobes in the Coarse Structure is given by:
.Note that the pulse width (
) appears on the bottom of this equation and determines the lobe spacing. Smaller pulse widths result in wider lobes and therefore greater bandwidth. and since the period of the PRF (T) appears at the top of the fine spectrum equation, there will be fewer lines if higher PRFs are used. These facts affect the decisions made by radar designers when considering the trade-offs that need to be made when trying to overcome the ambiguities that affect radar signals.Pulse profiling
If the rise and fall times of the modulation pulses are zero, (e.g. the pulse edges are infinitely sharp), then the sidebands will be as shown in the spectral diagrams above. The bandwidth consumed by this transmission can be huge and the total power transmitted is distributed over many hundreds of spectral lines. This is a potential source of interference with any other device and frequency-dependent imperfections in the transmit chain mean that some of this power never arrives at the antenna. In reality of course, it is impossible to achieve such sharp edges, so in practical systems the sidebands contain far fewer lines than a perfect system. If the bandwidth can be limited to include relatively few sidebands, by rolling off the pulse edges intentionally, an efficient system can be realised with the minimum of potential for interference with nearby equipment. However, the trade-off of this is that slow edges make range resolution poor. Early radars limited the bandwidth through filtration in the transmit chain, e.g. the waveguide, scanner etc., but performance could be sporadic with unwanted signals breaking through at remote frequencies and the edges of the recovered pulse being indeterminate. Further examination of the basic Radar Spectrum shown above shows that the information in the various lobes of the Coarse Spectrum is identical to that contained in the main lobe, so limiting the transmit and receive bandwidth to that extent provides significant benefits in terms of efficiency and noise reduction.Pulse compression
Pulse compression is a signal processing technique mainly used in radar, sonar and echography to increase the range resolution as well as the signal to noise ratio...
, then a good compromise between efficiency, performance and range resolution can be realised. The diagram on the left shows the effect on the spectrum if a trapezoid pulse profile is adopted. It can be seen that the energy in the sidebands is significantly reduced compared to the main lobe and the amplitude of the main lobe is increased.
There are many other profiles that can be adopted to optimise the performance of the system, but cosine and trapezoid profiles generally provide a good compromise between efficiency and resolution and so tend to be used most frequently.
Unambiguous velocity
Pulse-doppler radar
Pulse-Doppler is a 4D radar system capable of detecting both target 3D location as well as measuring radial velocity . It uses the Doppler effect to avoid overloading computers and operators as well as to reduce power consumption...
, which uses the Doppler effect
Doppler effect
The Doppler effect , named after Austrian physicist Christian Doppler who proposed it in 1842 in Prague, is the change in frequency of a wave for an observer moving relative to the source of the wave. It is commonly heard when a vehicle sounding a siren or horn approaches, passes, and recedes from...
to resolve velocity from the apparent change in frequency caused by targets that have net radial velocities compared to the radar device. Examination of the spectrum generated by a pulsed transmitter, shown above, reveals that each of the sidebands, (both coarse and fine), will be subject to the Doppler effect, another good reason to limit bandwidth and spectral complexity by pulse profiling.
Consider the positive shift caused by the closing target in the diagram which has been highly simplified for clarity.
It can be seen that as the relative velocity increases, a point will be reached where the spectral lines that constitute the echoes are hidden or aliased
Aliasing
In signal processing and related disciplines, aliasing refers to an effect that causes different signals to become indistinguishable when sampled...
by the next sideband of the modulated carrier.
Transmission of multiple pulse-packets with different PRF-values, e.g. staggered PRFs, will resolve this ambiguity, since each new PRF value will result in a new sideband position, revealing the velocity to the receiver. The maximum unambiguous target velocity is given by:
Typical system parameters
Taking all of the above characteristics into account means that certain constraints are placed on the radar designer. For example, a system with a 3 GHz carrier frequency and a pulse width of 1us will have a carrier period of approximately 333ps. Each transmitted pulse will contain about 3000 carrier cycles and the velocity and range ambiguity values for such a system would be:| PRF | Velocity Ambiguity | Range Ambiguity |
|---|---|---|
| Low (2 kHz) | 50 m/s | 75 km |
| Medium (12 kHz) | 300 m/s | 12.5 km |
| High (200 kHz) | 5000 m/s | 750 m |
See also
- RadarRadarRadar is an object-detection system which uses radio waves to determine the range, altitude, direction, or speed of objects. It can be used to detect aircraft, ships, spacecraft, guided missiles, motor vehicles, weather formations, and terrain. The radar dish or antenna transmits pulses of radio...
- Doppler radarDoppler radarA Doppler radar is a specialized radar that makes use of the Doppler effect to produce velocity data about objects at a distance. It does this by beaming a microwave signal towards a desired target and listening for its reflection, then analyzing how the frequency of the returned signal has been...
- Pulse-Doppler radarPulse-doppler radarPulse-Doppler is a 4D radar system capable of detecting both target 3D location as well as measuring radial velocity . It uses the Doppler effect to avoid overloading computers and operators as well as to reduce power consumption...
- Weather radarWeather radarWeather radar, also called weather surveillance radar and Doppler weather radar, is a type of radar used to locate precipitation, calculate its motion, estimate its type . Modern weather radars are mostly pulse-Doppler radars, capable of detecting the motion of rain droplets in addition to the...
(pulsed with doppler processing) - Continuous-wave radarContinuous-wave radarContinuous-wave radar is a type of radar system where a known stable frequency continuous wave radio energy is transmitted and then received from any reflecting objects.Continuous wave radar uses Doppler, which renders the radar immune to interference from large stationary objects and slow moving...
(non-pulsed, pure doppler processing) - AliasingAliasingIn signal processing and related disciplines, aliasing refers to an effect that causes different signals to become indistinguishable when sampled...
- the reason for ambiguous velocity estimates