![](http://image.absoluteastronomy.com/images//topicimages/noimage.gif)
Valve float
Encyclopedia
Valve float is an adverse condition which occurs when the poppet valve
s on an internal combustion engine
valvetrain
do not remain in contact with the camshaft
lobe during the valve closure phase of the cam lobe profile. This reduces engine efficiency and performance and potentially increases engine emissions
.
Valve bounce is a related condition where the valve does not stay seated
, due to the combined effects of the valve's inertia
and resonance
effects of metallic valve springs that effectively reduce the closing force, and allow the valve to re-open partially.
es and higher stresses in the valvetrain system. Various techniques have been used to offset the effect of stiffer springs, such as dual-spring and progressive-sprung valves, roller-tipped tappet
s, and pneumatic valves.
to push the valve closed. Formula One
racing engine manufacturers use a pneumatic system to close the valves to allow for very high RPM without valve float.
Poppet valve
A poppet valve is a valve consisting of a hole, usually round or oval, and a tapered plug, usually a disk shape on the end of a shaft also called a valve stem. The shaft guides the plug portion by sliding through a valve guide...
s on an internal combustion engine
Internal combustion engine
The internal combustion engine is an engine in which the combustion of a fuel occurs with an oxidizer in a combustion chamber. In an internal combustion engine, the expansion of the high-temperature and high -pressure gases produced by combustion apply direct force to some component of the engine...
valvetrain
Valvetrain
Valvetrain is an all-encompassing term used to describe the mechanisms and parts which control the operation of the valves. A traditional reciprocating internal combustion engine uses valves to control air and fuel flow into and out of the cylinders, facilitating combustion.-Layout:Valvetrain: The...
do not remain in contact with the camshaft
Camshaft
A camshaft is a shaft to which a cam is fastened or of which a cam forms an integral part.-History:An early cam was built into Hellenistic water-driven automata from the 3rd century BC. The camshaft was later described in Iraq by Al-Jazari in 1206. He employed it as part of his automata,...
lobe during the valve closure phase of the cam lobe profile. This reduces engine efficiency and performance and potentially increases engine emissions
Pollution
Pollution is the introduction of contaminants into a natural environment that causes instability, disorder, harm or discomfort to the ecosystem i.e. physical systems or living organisms. Pollution can take the form of chemical substances or energy, such as noise, heat or light...
.
Similar conditions
Valve loft is utilizing a controlled float to increase lift and duration of the valve open cycle. In some motorsports there are rules that limit camshaft lift; therefore, provoking this type of exploitation. By properly optimizing the system, one can actually achieve this without undue stresses added to the camshaft lobes and tappets (lifters).Valve bounce is a related condition where the valve does not stay seated
Valve seat
The valve seat in an internal combustion gasoline or diesel engine is the surface against which an intake or an exhaust valve rests during the portion of the engine operating cycle when that valve is closed...
, due to the combined effects of the valve's inertia
Inertia
Inertia is the resistance of any physical object to a change in its state of motion or rest, or the tendency of an object to resist any change in its motion. It is proportional to an object's mass. The principle of inertia is one of the fundamental principles of classical physics which are used to...
and resonance
Resonance
In physics, resonance is the tendency of a system to oscillate at a greater amplitude at some frequencies than at others. These are known as the system's resonant frequencies...
effects of metallic valve springs that effectively reduce the closing force, and allow the valve to re-open partially.
Remedies
Stiffer valve springs can help prevent valve float and valve bounce, but only at the expense of increased friction lossFriction loss
Friction loss refers to that portion of pressure lost by fluids while moving through a pipe, hose, or other limited space. In mechanical systems such as internal combustion engines, it refers to the power lost overcoming the friction between two moving surfaces.- Causes :Friction loss has several...
es and higher stresses in the valvetrain system. Various techniques have been used to offset the effect of stiffer springs, such as dual-spring and progressive-sprung valves, roller-tipped tappet
Tappet
A tappet is the noise made by a worn cam follower, however the term is widely used to represent the cam follower itself. In mechanical engineering it is a projection which imparts a linear motion to some other component within an assembly...
s, and pneumatic valves.
Alternative solutions
Italian motorcycle manufacturer Ducati uses the desmodromic (springless) valve system to counter this problem and allow for higher engine speeds. The system consists of a mechanical lifter mechanism that uses a second rocker armRocker arm
Generally referred to within the internal combustion engine of automotive, marine, motorcycle and reciprocating aviation engines, the rocker arm is a reciprocating lever that conveys radial movement from the cam lobe into linear movement at the poppet valve to open it...
to push the valve closed. Formula One
Formula One
Formula One, also known as Formula 1 or F1 and referred to officially as the FIA Formula One World Championship, is the highest class of single seater auto racing sanctioned by the Fédération Internationale de l'Automobile . The "formula" designation in the name refers to a set of rules with which...
racing engine manufacturers use a pneumatic system to close the valves to allow for very high RPM without valve float.