Gas filled tube
Encyclopedia
A gas-filled tube, also known as a discharge tube, is an arrangement of electrode
s in a gas
within an insulating
, temperature-resistant envelope
. Although the envelope is typically glass
, power tubes often use ceramic
s, and military
tubes often use glass-lined metal. Gas tubes are tubes whose electrical characteristics are substantially influenced by the pressure and composition of gas contained inside.
Gas-filled tubes exploit phenomena related to electric discharge in gases
, operating by ionizing the gas with applied voltage
to start electrical conduction. Both hot cathode
and cold cathode
type devices are encountered. Depending on application, either the glow from the gas or the electric arc
or electric glow discharge
may be the desired function.
is used in tubes used for very fast switching, e.g. some thyratron
s, dekatron
s, and krytron
s, where very steep edges are required. The build-up and recovery times of hydrogen are much shorter than in other gases. Hydrogen thyratrons are usually hot-cathode. Hydrogen (and deuterium) can be stored in the tube in the form of a metal hydride
, heated with an auxiliary filament; releasing hydrogen by heating such storage element can be used to replenish cleaned-up gas, and even to adjust the pressure as needed for a thyratron operation at a given voltage.
is used in ultraviolet
lamps for ultraviolet spectroscopy, in neutron generator
tubes, and in special tubes (e.g. crossatron
). It has higher breakdown voltage than hydrogen. In fast switching tubes it is used instead of hydrogen where high voltage operation is required. For a comparison, the hydrogen-filled CX1140 thyratron has anode voltage rating of 25 kV, while the deuterium-filled and otherwise identical CX1159 has 33 kV. Also, at the same voltage the pressure of deuterium can be higher than of hydrogen, allowing higher rise rates of rise of current before it causes excessive anode dissipation. Significantly higher peak powers are achievable. Its recovery time is however about 40% slower than for hydrogen.
es are frequently used in tubes for many purposes, from lighting to switching. Pure noble gases are employed in switching tubes. Noble gas filled thyratrons have better electrical parameters than mercury-based ones. The electrodes undergo damage by high-velocity ions. The neutral atoms of the gas slow the ions down by collisions, and reduce the energy transferred to the electrodes by the ion impact. Gases with high molecular weight, e.g. xenon, protect the electrodes better than lighter ones, e.g. neon.
s, are favored as they rapidly recombine with the ions present in the discharge channel. One of the most popular choices is sulfur hexafluoride
, used in special high-voltage applications. Other common options are dry pressurized nitrogen
and halocarbon
s.
; most commonly, pressures between 1–10 torr are used. The gas pressure influences the following factors:
Above a certain value, the higher the gas pressure, the higher the ignition voltage. High-pressure lighting tubes can require a few kilovolts impulse for ignition when cold, when the gas pressure is low. After warming up, when the volatile compound used for light emission is vaporized and the pressure increases, reignition of the discharge requires either significantly higher voltage or reducing the internal pressure by cooling down the lamp. For example, many sodium vapor lamps cannot be re-lit immediately after being shut off; they must cool down before they can be lit up again.
The gas tends to be used up during the tube operation, by several phenomena collectively called clean-up. The gas atoms or molecules are adsorbed
on the surfaces of the electrodes. In high voltage tubes, the accelerated ions can penetrate into the electrode materials. New surfaces, formed by sputtering of the electrodes and deposited on e.g. the inner surfaces of the tube, also readily adsorb gases. Non-inert gases can also chemically react with the tube components. Hydrogen may diffuse through some metals.
For removal of gas in vacuum tubes, getter
s are used. For resupplying gas for gas-filled tubes, replenishers are employed. Most commonly, replenishers are used with hydrogen; a filament made from a hydrogen-absorbing metal (e.g. zirconium or titanium) is present in the tube, and by controlling its temperature the ratio of absorbed and desorbed hydrogen is adjusted, resulting in controlling of the hydrogen pressure in the tube. The metal filament acts as a hydrogen storage. This approach is used in e.g. hydrogen thyratrons or neutron tubes. Usage of saturated mercury vapor allows using a pool of liquid mercury as a large storage of material; the atoms lost by clean-up are automatically replenished by evaporation of more mercury. The pressure in the tube is however strongly dependent on the mercury temperature, which has to be controlled carefully.
The gas used dramatically influences the parameters of the tube. The breakdown voltage depends on the gas composition and electrode distance; the dependencies are described by Paschen's law
.
Pure inert gases are used where the difference between the ignition voltage and the burning voltage has to be high, e.g. in switching tubes. Tubes for indication and stabilization, where the difference has to be lower, tend to be filled with Penning mixture
s; the lower difference between ignition and burning voltages allows using lower power supply voltages and smaller series resistances.
Large rectifiers use saturated mercury vapor with a small amount of an inert gas. The inert gas supports the discharge when the tube is cold.
The mercury arc valve current-voltage characteristics are highly dependent on the temperature of the liquid mercury. The voltage drop in forward bias decreases from about 60 volts at 0 °C to somewhat above 10 volts at 50 °C and then stays constant; the reverse bias breakdown ("arc-back") voltage drops dramatically with temperature, from 36 kV at 60 °C to 12 kV at 80 °C to even less at higher temperatures. The operating range is therefore usually between 18–65 °C.
The gas in the tube has to be kept pure to maintain the desired properties; even small amount of impurities can dramatically change the tube values; presence of non-inert gases generally increases the breakdown and burning voltages. The presence of impurities can be observed by changes in the glow color of the gas. Air leaking into the tube makes the discharge look pale, milky, or reddish. Traces of mercury vapors glow bluish, obscuring the original gas color. Magnesium vapor colors the discharge green. To prevent outgassing
of the tube components during operation, a bake-out
is required before filling with gas and sealing. Thorough degassing is required for high-quality tubes; even as little as 10−8 torr of oxygen is sufficient for covering the electrodes with monomolecular oxide layer in few hours. Non-inert gases can be removed by suitable getter
s. for mercury-containing tubes, getters that do not form amalgam
s with mercury (e.g. zirconium
, but not barium
) have to be used. Cathode sputtering may be used intentionally for gettering non-inert gases; some reference tubes use molybdenum
cathodes for this purpose.
, CFL lamps
, mercury
and sodium discharge lamps
and HID lamps
are all gas-filled tubes used for lighting.
Neon lamp
s and neon signage (most of which is not neon based these days) are also low-pressure gas-filled tubes.
Specialized historic low-pressure gas-filled tube devices include the Nixie tube
(used to display numerals) and the Decatron (used to count or divide pulses, with display as a secondary function).
Xenon flash lamps are gas-filled tubes used in camera
s and strobe light
s to produce bright flashes of light.
The recently developed sulfur lamp
s are also gas-filled tubes when hot.
, krytron
, and ignitron
tubes, which are used to switch high-voltage currents. A specialized type of gas-filled tube called a Gas Discharge Tube (GDT) is fabricated for use in surge protector
s, to limit voltage surges in electrical and electronic circuits.
Electrode
An electrode is an electrical conductor used to make contact with a nonmetallic part of a circuit...
s in a gas
Gas
Gas is one of the three classical states of matter . Near absolute zero, a substance exists as a solid. As heat is added to this substance it melts into a liquid at its melting point , boils into a gas at its boiling point, and if heated high enough would enter a plasma state in which the electrons...
within an insulating
Dielectric
A dielectric is an electrical insulator that can be polarized by an applied electric field. When a dielectric is placed in an electric field, electric charges do not flow through the material, as in a conductor, but only slightly shift from their average equilibrium positions causing dielectric...
, temperature-resistant envelope
Envelope
An envelope is a common packaging item, usually made of thin flat material. It is designed to contain a flat object, such as a letter or card....
. Although the envelope is typically glass
Glass
Glass is an amorphous solid material. Glasses are typically brittle and optically transparent.The most familiar type of glass, used for centuries in windows and drinking vessels, is soda-lime glass, composed of about 75% silica plus Na2O, CaO, and several minor additives...
, power tubes often use ceramic
Ceramic
A ceramic is an inorganic, nonmetallic solid prepared by the action of heat and subsequent cooling. Ceramic materials may have a crystalline or partly crystalline structure, or may be amorphous...
s, and military
Military
A military is an organization authorized by its greater society to use lethal force, usually including use of weapons, in defending its country by combating actual or perceived threats. The military may have additional functions of use to its greater society, such as advancing a political agenda e.g...
tubes often use glass-lined metal. Gas tubes are tubes whose electrical characteristics are substantially influenced by the pressure and composition of gas contained inside.
Gas-filled tubes exploit phenomena related to electric discharge in gases
Electric discharge in gases
Electric discharge in gases occurs when electric current flows through a gaseous medium. Depending on several factors, the discharge may radiate visible light.-Discharge types:...
, operating by ionizing the gas with applied voltage
Voltage
Voltage, otherwise known as electrical potential difference or electric tension is the difference in electric potential between two points — or the difference in electric potential energy per unit charge between two points...
to start electrical conduction. Both hot cathode
Hot cathode
In vacuum tubes, a hot cathode is a cathode electrode which emits electrons due to thermionic emission. In the accelerator community, these are referred to as thermionic cathodes. The heating element is usually an electrical filament...
and cold cathode
Cold cathode
A cold cathode is a cathode used within nixie tubes, gas discharge lamps, discharge tubes, and some types of vacuum tube which is not electrically heated by the circuit to which it is connected...
type devices are encountered. Depending on application, either the glow from the gas or the electric arc
Electric arc
An electric arc is an electrical breakdown of a gas which produces an ongoing plasma discharge, resulting from a current flowing through normally nonconductive media such as air. A synonym is arc discharge. An arc discharge is characterized by a lower voltage than a glow discharge, and relies on...
or electric glow discharge
Electric glow discharge
An electric glow discharge is a plasma formed by the passage of current at 100 V to several kV through a gas, often argon or another noble gas. It is found in products such as neon lamps and plasma-screen televisions, and is used in plasma physics and analytical chemistry.-Basic operating...
may be the desired function.
Hydrogen
HydrogenHydrogen
Hydrogen is the chemical element with atomic number 1. It is represented by the symbol H. With an average atomic weight of , hydrogen is the lightest and most abundant chemical element, constituting roughly 75% of the Universe's chemical elemental mass. Stars in the main sequence are mainly...
is used in tubes used for very fast switching, e.g. some thyratron
Thyratron
A thyratron is a type of gas filled tube used as a high energy electrical switch and controlled rectifier. Triode, tetrode and pentode variations of the thyratron have been manufactured in the past, though most are of the triode design...
s, dekatron
Dekatron
In electronics, a Dekatron is a gas-filled decade counting tube. Dekatrons were used in computers, calculators and other counting-related products during the 1950s and 1960s...
s, and krytron
Krytron
The krytron is a cold-cathode gas filled tube intended for use as a very high-speed switch, and was one of the earliest developments of the EG&G Corporation. It is somewhat similar to thyratron...
s, where very steep edges are required. The build-up and recovery times of hydrogen are much shorter than in other gases. Hydrogen thyratrons are usually hot-cathode. Hydrogen (and deuterium) can be stored in the tube in the form of a metal hydride
Hydride
In chemistry, a hydride is the anion of hydrogen, H−, or, more commonly, a compound in which one or more hydrogen centres have nucleophilic, reducing, or basic properties. In compounds that are regarded as hydrides, hydrogen is bonded to a more electropositive element or group...
, heated with an auxiliary filament; releasing hydrogen by heating such storage element can be used to replenish cleaned-up gas, and even to adjust the pressure as needed for a thyratron operation at a given voltage.
Deuterium
DeuteriumDeuterium
Deuterium, also called heavy hydrogen, is one of two stable isotopes of hydrogen. It has a natural abundance in Earth's oceans of about one atom in of hydrogen . Deuterium accounts for approximately 0.0156% of all naturally occurring hydrogen in Earth's oceans, while the most common isotope ...
is used in ultraviolet
Ultraviolet
Ultraviolet light is electromagnetic radiation with a wavelength shorter than that of visible light, but longer than X-rays, in the range 10 nm to 400 nm, and energies from 3 eV to 124 eV...
lamps for ultraviolet spectroscopy, in neutron generator
Neutron generator
Neutron generators are neutron source devices which contain compact linear accelerators and that produce neutrons by fusing isotopes of hydrogen together. The fusion reactions take place in these devices by accelerating either deuterium, tritium, or a mixture of these two isotopes into a metal...
tubes, and in special tubes (e.g. crossatron
Crossatron
In electronics, a crossatron is a high-power pulsed modulator device, a cold cathode gas-filled tube that combines the best features of thyratrons, vacuum tubes, and power semiconductor switches...
). It has higher breakdown voltage than hydrogen. In fast switching tubes it is used instead of hydrogen where high voltage operation is required. For a comparison, the hydrogen-filled CX1140 thyratron has anode voltage rating of 25 kV, while the deuterium-filled and otherwise identical CX1159 has 33 kV. Also, at the same voltage the pressure of deuterium can be higher than of hydrogen, allowing higher rise rates of rise of current before it causes excessive anode dissipation. Significantly higher peak powers are achievable. Its recovery time is however about 40% slower than for hydrogen.
Noble gases
Noble gasNoble gas
The noble gases are a group of chemical elements with very similar properties: under standard conditions, they are all odorless, colorless, monatomic gases, with very low chemical reactivity...
es are frequently used in tubes for many purposes, from lighting to switching. Pure noble gases are employed in switching tubes. Noble gas filled thyratrons have better electrical parameters than mercury-based ones. The electrodes undergo damage by high-velocity ions. The neutral atoms of the gas slow the ions down by collisions, and reduce the energy transferred to the electrodes by the ion impact. Gases with high molecular weight, e.g. xenon, protect the electrodes better than lighter ones, e.g. neon.
- HeliumHeliumHelium is the chemical element with atomic number 2 and an atomic weight of 4.002602, which is represented by the symbol He. It is a colorless, odorless, tasteless, non-toxic, inert, monatomic gas that heads the noble gas group in the periodic table...
is used in helium-neon laserHelium-neon laserA helium–neon laser or HeNe laser, is a type of gas laser whose gain medium consists of a mixture of helium and neon inside of a small bore capillary tube, usually excited by a DC electrical discharge.- History of HeNe laser development:...
s and in some thyratrons rated for high currents and high voltages. Helium provides about as short deionization time as hydrogen, but can withstand lower voltage, so it is used much less often. - NeonNeonNeon is the chemical element that has the symbol Ne and an atomic number of 10. Although a very common element in the universe, it is rare on Earth. A colorless, inert noble gas under standard conditions, neon gives a distinct reddish-orange glow when used in either low-voltage neon glow lamps or...
has low ignition voltage and is frequently used in low-voltage tubes. Discharge in neon emits relatively bright red light; neon-filled switching tubes therefore also act as indicators, shining red when switched on. This is exploited in the decatron tubes, which act as both counters and displays. Its red light is exploited in neon signage. Used in fluorescent tubes with high power and short length, e.g. industrial lighting tubes. Has higher voltage drop in comparison with argon and krypton. Its low atomic mass provides only a little protection to the electrodes against accelerated ions; additional screening wires or plates can be used for prolonging the anode lifetime. In fluorescent tubes it is used in combination with mercury. - ArgonArgonArgon is a chemical element represented by the symbol Ar. Argon has atomic number 18 and is the third element in group 18 of the periodic table . Argon is the third most common gas in the Earth's atmosphere, at 0.93%, making it more common than carbon dioxide...
was the first gas used in fluorescent tubes and is still frequently used due to its low cost, high efficiency, and very low striking voltage. In fluorescent tubes it is used in combination with mercury. It was also used in early rectifier tubes; first thyratrons were derived from such argon-filled tubes. - KryptonKryptonKrypton is a chemical element with the symbol Kr and atomic number 36. It is a member of Group 18 and Period 4 elements. A colorless, odorless, tasteless noble gas, krypton occurs in trace amounts in the atmosphere, is isolated by fractionally distilling liquified air, and is often used with other...
can be used in fluorescent lamps instead of argon; in that application it reduces the total energy losses on electrodes from about 15% to 7%. The voltage drop per lamp length is however lower than with argon, which can be compensated by smaller tube diameter. Krypton-filled lamps also require higher starting voltage; this can be alleviated by using e.g. 25%–75% argon-krypton mixture. In fluorescent tubes it is used in combination with mercury. - XenonXenonXenon is a chemical element with the symbol Xe and atomic number 54. The element name is pronounced or . A colorless, heavy, odorless noble gas, xenon occurs in the Earth's atmosphere in trace amounts...
in pure state has high breakdown voltage, making it useful in higher-voltage switching tubes. Xenon is also used as a component of gas mixtures when production of ultraviolet radiation is required, e.g. in plasma displayPlasma displayA plasma display panel is a type of flat panel display common to large TV displays or larger. They are called "plasma" displays because the technology utilizes small cells containing electrically charged ionized gases, or what are in essence chambers more commonly known as fluorescent...
s, usually to excite a phosphorPhosphorA phosphor, most generally, is a substance that exhibits the phenomenon of luminescence. Somewhat confusingly, this includes both phosphorescent materials, which show a slow decay in brightness , and fluorescent materials, where the emission decay takes place over tens of nanoseconds...
. The wavelength produced is longer than with argon and krypton and penetrates the phosphorPhosphorA phosphor, most generally, is a substance that exhibits the phenomenon of luminescence. Somewhat confusingly, this includes both phosphorescent materials, which show a slow decay in brightness , and fluorescent materials, where the emission decay takes place over tens of nanoseconds...
s better. To lower the ionization voltage, neon-xenon or helium-xenon are used; above 350 torr, helium has lower breakdown voltage than neon and vice versa. At concentrations of 1% and less of xenon, the Penning effect becomes significant in such mixtures, as most of xenon ionization occurs by collision with excited atoms of the other noble gas; at more than few percents of xenon, the discharge ionizes xenon directly due to most energy of the electrons being spent on direct ionization of xenon. - Penning mixturePenning mixtureA Penning mixture , named after Frans Michel Penning, is a mixture of gases used in electric lighting or displaying fixtures. Although the popular phrase for the most common of these is a neon lamp, it's more efficient to have the glass tube filled not with pure neon, but with a Penning mixture,...
s are used where lower ionization voltage is required, e.g., in the neon lampNeon lampA neon lamp is a miniature gas discharge lamp that typically contains neon gas at a low pressure in a glass capsule. Only a thin region adjacent to the electrodes glows in these lamps, which distinguishes them from the much longer and brighter neon tubes used for signage...
s, Geiger-Muller tubeGeiger-Müller tubeA Geiger–Müller tube is the sensing element of a Geiger counter instrument that can detect a single particle of ionizing radiation, and typically produce an audible click for each. It was named for Hans Geiger who invented the device in 1908, and Walther Müller who collaborated with Geiger in...
s and other gas-filled particle detectorParticle detectorIn experimental and applied particle physics, nuclear physics, and nuclear engineering, a particle detector, also known as a radiation detector, is a device used to detect, track, and/or identify high-energy particles, such as those produced by nuclear decay, cosmic radiation, or reactions in a...
s. A classical combination is about 98–99.5% of neonNeonNeon is the chemical element that has the symbol Ne and an atomic number of 10. Although a very common element in the universe, it is rare on Earth. A colorless, inert noble gas under standard conditions, neon gives a distinct reddish-orange glow when used in either low-voltage neon glow lamps or...
with 0.5–2% of argonArgonArgon is a chemical element represented by the symbol Ar. Argon has atomic number 18 and is the third element in group 18 of the periodic table . Argon is the third most common gas in the Earth's atmosphere, at 0.93%, making it more common than carbon dioxide...
, used in, e.g., neon bulbs and in monochrome plasma displayPlasma displayA plasma display panel is a type of flat panel display common to large TV displays or larger. They are called "plasma" displays because the technology utilizes small cells containing electrically charged ionized gases, or what are in essence chambers more commonly known as fluorescent...
s.
Elemental vapors (metals and nonmetals)
- MercuryMercury (element)Mercury is a chemical element with the symbol Hg and atomic number 80. It is also known as quicksilver or hydrargyrum...
vapors are used for applications with high current, e.g. lights, mercury arc valveMercury arc valveA mercury-arc valve is a type of electrical rectifier used for converting high-voltage or high-current alternating current into direct current . Rectifiers of this type were used to provide power for industrial motors, electric railways, streetcars, and electric locomotives, as well as for...
s, ignitronIgnitronAn ignitron is a type of controlled rectifier dating from the 1930s. Invented by Joseph Slepian while employed by Westinghouse, Westinghouse was the original manufacturer and owned trademark rights to the name "Ignitron"....
s. Mercury is used because of its high vapor pressure and low ionization potential. Mercury mixed with an inert gas is used where the energy losses in the tube have to be low and the tube lifetime should be long. In mercury-inert gas mixtures, the discharge is initially carried primarily by the inert gas; the released heat then serves to evaporate enough mercury to reach the desired vapor pressure. Low-voltage (hundreds volts) rectifiers use saturated mercury vapor in combination with a small amount of inert gas, allowing cold start of the tubes. High-voltage (kilovolts and more) rectifiers use pure mercury vapor at low pressure, requiring maintenance of maximum temperature of the tube. The liquid mercury serves as a reservoir of mercury, replenishing the vapors that are used up during the discharge. Unsaturated mercury vapor can be used, but as it can not be replenished, the lifetime of such tubes is lower. The strong dependence of vapor pressure on mercury temperature limits the environments the mercury-based tubes can operate in. In low-pressure mercury lamps, there is an optimum mercury pressure for the highest efficiency. Photons emitted by ionized mercury atoms can be absorbed by nearby nonionized atoms and either reradiated or the atom is deexcited nonradiatively, too high mercury pressure therefore causes losses of light. Too low mercury pressure leads to too few atoms present to get ionized and radiate photons. The optimum temperature for low-pressure mercury lamps is at about 42 °C, when the saturated vapor pressure of mercury (present as a drop of about 1 mg of liquid mercury in the tube, as a reservoir compensating for losses by clean-up) reaches this optimum. In lamps intended for operation at higher ambient temperatures, and at a wider temperature range, mercury is present in the form of an amalgamAmalgam (chemistry)An amalgam is a substance formed by the reaction of mercury with another metal. Almost all metals can form amalgams with mercury, notable exceptions being iron and platinum. Silver-mercury amalgams are important in dentistry, and gold-mercury amalgam is used in the extraction of gold from ore.The...
with e.g. bismuthBismuthBismuth is a chemical element with symbol Bi and atomic number 83. Bismuth, a trivalent poor metal, chemically resembles arsenic and antimony. Elemental bismuth may occur naturally uncombined, although its sulfide and oxide form important commercial ores. The free element is 86% as dense as lead...
and indiumIndiumIndium is a chemical element with the symbol In and atomic number 49. This rare, very soft, malleable and easily fusible post-transition metal is chemically similar to gallium and thallium, and shows the intermediate properties between these two...
; the vapor pressure above amalgam is lower than above liquid mercury. Mercury is used in fluorescent tubes as a source of visible and ultraviolet light for exciting the phosphorPhosphorA phosphor, most generally, is a substance that exhibits the phenomenon of luminescence. Somewhat confusingly, this includes both phosphorescent materials, which show a slow decay in brightness , and fluorescent materials, where the emission decay takes place over tens of nanoseconds...
; in that application it is usually used together with argon, or in some cases with krypton or neon. Mercury ions deionize slowly, limiting the switching speed of mercury-filled thyratrons. Ion bombardment with mercury ions of even relatively low energies also gradually destroys oxide-coated cathodes. - SodiumSodiumSodium is a chemical element with the symbol Na and atomic number 11. It is a soft, silvery-white, highly reactive metal and is a member of the alkali metals; its only stable isotope is 23Na. It is an abundant element that exists in numerous minerals, most commonly as sodium chloride...
vapors are used in sodium-vapor lamps. - SulfurSulfurSulfur or sulphur is the chemical element with atomic number 16. In the periodic table it is represented by the symbol S. It is an abundant, multivalent non-metal. Under normal conditions, sulfur atoms form cyclic octatomic molecules with chemical formula S8. Elemental sulfur is a bright yellow...
vapors are used in sulfur lampSulfur lampThe sulfur lamp is a highly efficient full-spectrum electrodeless lighting system whose light is generated by sulfur plasma that has been excited by microwave radiation. The technology was developed in the early 1990s, but, although it appeared initially to be very promising, sulfur lighting was...
s. - Vapors of many metals, alone or together with a noble gas, are used in many laserLaserA laser is a device that emits light through a process of optical amplification based on the stimulated emission of photons. The term "laser" originated as an acronym for Light Amplification by Stimulated Emission of Radiation...
s.
Other gases
- Air can be used in some low-demanding applications.
- NitrogenNitrogenNitrogen is a chemical element that has the symbol N, atomic number of 7 and atomic mass 14.00674 u. Elemental nitrogen is a colorless, odorless, tasteless, and mostly inert diatomic gas at standard conditions, constituting 78.08% by volume of Earth's atmosphere...
at relatively high pressure tends to be used in surge arresters, due to its short build-up time, giving the tubes fast response time to voltage surges. - HalogenHalogenThe halogens or halogen elements are a series of nonmetal elements from Group 17 IUPAC Style of the periodic table, comprising fluorine , chlorine , bromine , iodine , and astatine...
s and alcoholAlcoholIn chemistry, an alcohol is an organic compound in which the hydroxy functional group is bound to a carbon atom. In particular, this carbon center should be saturated, having single bonds to three other atoms....
vapors absorb ultraviolet radiation and have high electron affinity. When added to inert gases, they quench the discharge; this is exploited in e.g. Geiger-Muller tubeGeiger-Müller tubeA Geiger–Müller tube is the sensing element of a Geiger counter instrument that can detect a single particle of ionizing radiation, and typically produce an audible click for each. It was named for Hans Geiger who invented the device in 1908, and Walther Müller who collaborated with Geiger in...
s.
Insulating gases
In special cases (e.g., high voltage switches), gases with good dielectric properties and very high breakdown voltages are needed. Highly electronegative elements, e.g., halogenHalogen
The halogens or halogen elements are a series of nonmetal elements from Group 17 IUPAC Style of the periodic table, comprising fluorine , chlorine , bromine , iodine , and astatine...
s, are favored as they rapidly recombine with the ions present in the discharge channel. One of the most popular choices is sulfur hexafluoride
Sulfur hexafluoride
Sulfur hexafluoride is an inorganic, colorless, odorless, and non-flammable greenhouse gas. has an octahedral geometry, consisting of six fluorine atoms attached to a central sulfur atom. It is a hypervalent molecule. Typical for a nonpolar gas, it is poorly soluble in water but soluble in...
, used in special high-voltage applications. Other common options are dry pressurized nitrogen
Nitrogen
Nitrogen is a chemical element that has the symbol N, atomic number of 7 and atomic mass 14.00674 u. Elemental nitrogen is a colorless, odorless, tasteless, and mostly inert diatomic gas at standard conditions, constituting 78.08% by volume of Earth's atmosphere...
and halocarbon
Halocarbon
Halocarbon compounds are chemicals in which one or more carbon atoms are linked by covalent bonds with one or more halogen atoms resulting in the formation of organofluorine compounds, organochlorine compounds, organobromine compounds, and organoiodine compounds...
s.
Gas-tube physics and technology
The gas pressure may range between 0.001 and 1000 torrTorr
The torr is a non-SI unit of pressure with the ratio of 760 to 1 standard atmosphere, chosen to be roughly equal to the fluid pressure exerted by a millimetre of mercury, i.e., a pressure of 1 torr is approximately equal to 1 mmHg...
; most commonly, pressures between 1–10 torr are used. The gas pressure influences the following factors:
- breakdown voltageBreakdown voltageThe breakdown voltage of an insulator is the minimum voltage that causes a portion of an insulator to become electrically conductive.The breakdown voltage of a diode is the minimum reverse voltage to make the diode conduct in reverse...
(also called ignition voltage) - current densityCurrent densityCurrent density is a measure of the density of flow of a conserved charge. Usually the charge is the electric charge, in which case the associated current density is the electric current per unit area of cross section, but the term current density can also be applied to other conserved...
- operating voltage
- backfire voltage
- tube lifetime (lower pressure tubes tend to have shorter lifetimes due to using up of the gas)
- cathode sputteringSputteringSputtering is a process whereby atoms are ejected from a solid target material due to bombardment of the target by energetic particles. It is commonly used for thin-film deposition, etching and analytical techniques .-Physics of sputtering:...
, reduced at higher pressures
Above a certain value, the higher the gas pressure, the higher the ignition voltage. High-pressure lighting tubes can require a few kilovolts impulse for ignition when cold, when the gas pressure is low. After warming up, when the volatile compound used for light emission is vaporized and the pressure increases, reignition of the discharge requires either significantly higher voltage or reducing the internal pressure by cooling down the lamp. For example, many sodium vapor lamps cannot be re-lit immediately after being shut off; they must cool down before they can be lit up again.
The gas tends to be used up during the tube operation, by several phenomena collectively called clean-up. The gas atoms or molecules are adsorbed
Adsorption
Adsorption is the adhesion of atoms, ions, biomolecules or molecules of gas, liquid, or dissolved solids to a surface. This process creates a film of the adsorbate on the surface of the adsorbent. It differs from absorption, in which a fluid permeates or is dissolved by a liquid or solid...
on the surfaces of the electrodes. In high voltage tubes, the accelerated ions can penetrate into the electrode materials. New surfaces, formed by sputtering of the electrodes and deposited on e.g. the inner surfaces of the tube, also readily adsorb gases. Non-inert gases can also chemically react with the tube components. Hydrogen may diffuse through some metals.
For removal of gas in vacuum tubes, getter
Getter
A getter is a deposit of reactive material that is deliberately placed inside a vacuum system, for the purpose of completing and maintaining the vacuum. When gas molecules strike the getter material, they combine with it chemically or by adsorption...
s are used. For resupplying gas for gas-filled tubes, replenishers are employed. Most commonly, replenishers are used with hydrogen; a filament made from a hydrogen-absorbing metal (e.g. zirconium or titanium) is present in the tube, and by controlling its temperature the ratio of absorbed and desorbed hydrogen is adjusted, resulting in controlling of the hydrogen pressure in the tube. The metal filament acts as a hydrogen storage. This approach is used in e.g. hydrogen thyratrons or neutron tubes. Usage of saturated mercury vapor allows using a pool of liquid mercury as a large storage of material; the atoms lost by clean-up are automatically replenished by evaporation of more mercury. The pressure in the tube is however strongly dependent on the mercury temperature, which has to be controlled carefully.
The gas used dramatically influences the parameters of the tube. The breakdown voltage depends on the gas composition and electrode distance; the dependencies are described by Paschen's law
Paschen's law
Paschen's Law, named after Friedrich Paschen, was first stated in 1889. He studied the breakdown voltage of gas between parallel plates as a function of pressure and gap distance. The voltage necessary to arc across the gap decreased up to a point as the pressure was reduced. It then increased,...
.
Pure inert gases are used where the difference between the ignition voltage and the burning voltage has to be high, e.g. in switching tubes. Tubes for indication and stabilization, where the difference has to be lower, tend to be filled with Penning mixture
Penning mixture
A Penning mixture , named after Frans Michel Penning, is a mixture of gases used in electric lighting or displaying fixtures. Although the popular phrase for the most common of these is a neon lamp, it's more efficient to have the glass tube filled not with pure neon, but with a Penning mixture,...
s; the lower difference between ignition and burning voltages allows using lower power supply voltages and smaller series resistances.
Large rectifiers use saturated mercury vapor with a small amount of an inert gas. The inert gas supports the discharge when the tube is cold.
The mercury arc valve current-voltage characteristics are highly dependent on the temperature of the liquid mercury. The voltage drop in forward bias decreases from about 60 volts at 0 °C to somewhat above 10 volts at 50 °C and then stays constant; the reverse bias breakdown ("arc-back") voltage drops dramatically with temperature, from 36 kV at 60 °C to 12 kV at 80 °C to even less at higher temperatures. The operating range is therefore usually between 18–65 °C.
The gas in the tube has to be kept pure to maintain the desired properties; even small amount of impurities can dramatically change the tube values; presence of non-inert gases generally increases the breakdown and burning voltages. The presence of impurities can be observed by changes in the glow color of the gas. Air leaking into the tube makes the discharge look pale, milky, or reddish. Traces of mercury vapors glow bluish, obscuring the original gas color. Magnesium vapor colors the discharge green. To prevent outgassing
Outgassing
Outgassing is the release of a gas that was dissolved, trapped, frozen or absorbed in some material. As an example, research has shown how the concentration of carbon dioxide in the Earth's atmosphere has sometimes been linked to ocean outgassing...
of the tube components during operation, a bake-out
Bake-out
Bake-out is a term used in several areas of technology, fabrication, and in building construction, referring to the act of using heat and sometimes a vacuum to release volatile compounds from something as a form of cleaning or processing...
is required before filling with gas and sealing. Thorough degassing is required for high-quality tubes; even as little as 10−8 torr of oxygen is sufficient for covering the electrodes with monomolecular oxide layer in few hours. Non-inert gases can be removed by suitable getter
Getter
A getter is a deposit of reactive material that is deliberately placed inside a vacuum system, for the purpose of completing and maintaining the vacuum. When gas molecules strike the getter material, they combine with it chemically or by adsorption...
s. for mercury-containing tubes, getters that do not form amalgam
Amalgam (chemistry)
An amalgam is a substance formed by the reaction of mercury with another metal. Almost all metals can form amalgams with mercury, notable exceptions being iron and platinum. Silver-mercury amalgams are important in dentistry, and gold-mercury amalgam is used in the extraction of gold from ore.The...
s with mercury (e.g. zirconium
Zirconium
Zirconium is a chemical element with the symbol Zr and atomic number 40. The name of zirconium is taken from the mineral zircon. Its atomic mass is 91.224. It is a lustrous, grey-white, strong transition metal that resembles titanium...
, but not barium
Barium
Barium is a chemical element with the symbol Ba and atomic number 56. It is the fifth element in Group 2, a soft silvery metallic alkaline earth metal. Barium is never found in nature in its pure form due to its reactivity with air. Its oxide is historically known as baryta but it reacts with...
) have to be used. Cathode sputtering may be used intentionally for gettering non-inert gases; some reference tubes use molybdenum
Molybdenum
Molybdenum , is a Group 6 chemical element with the symbol Mo and atomic number 42. The name is from Neo-Latin Molybdaenum, from Ancient Greek , meaning lead, itself proposed as a loanword from Anatolian Luvian and Lydian languages, since its ores were confused with lead ores...
cathodes for this purpose.
Lighting and display gas-filled tubes
Fluorescent lightingFluorescent lamp
A fluorescent lamp or fluorescent tube is a gas-discharge lamp that uses electricity to excite mercury vapor. The excited mercury atoms produce short-wave ultraviolet light that then causes a phosphor to fluoresce, producing visible light. A fluorescent lamp converts electrical power into useful...
, CFL lamps
Compact fluorescent lamp
A compact fluorescent lamp , also called compact fluorescent light, energy-saving light, and compact fluorescent tube, is a fluorescent lamp designed to replace an incandescent lamp; some types fit into light fixtures formerly used for incandescent lamps...
, mercury
Mercury-vapor lamp
A mercury-vapor lamp is a gas discharge lamp that uses an electric arc through vaporized mercury to produce light. The arc discharge is generally confined to a small fused quartz arc tube mounted within a larger borosilicate glass bulb...
and sodium discharge lamps
Sodium vapor lamp
A sodium vapor lamp is a gas discharge lamp that uses sodium in an excited state to produce light. There are two varieties of such lamps: low pressure and high pressure...
and HID lamps
Metal halide lamp
Metal-halide lamps, a member of the high-intensity discharge family of lamps, produce high light output for their size, making them a compact, powerful, and efficient light source. By adding rare earth metal salts to the mercury vapor lamp, improved luminous efficacy and light color is obtained...
are all gas-filled tubes used for lighting.
Neon lamp
Neon lamp
A neon lamp is a miniature gas discharge lamp that typically contains neon gas at a low pressure in a glass capsule. Only a thin region adjacent to the electrodes glows in these lamps, which distinguishes them from the much longer and brighter neon tubes used for signage...
s and neon signage (most of which is not neon based these days) are also low-pressure gas-filled tubes.
Specialized historic low-pressure gas-filled tube devices include the Nixie tube
Nixie tube
A nixie tube is an electronic device for displaying numerals or other information. The glass tube contains a wire-mesh anode and multiple cathodes. In most tubes, the cathodes are shaped like numerals. Applying power to one cathode surrounds it with an orange glow discharge...
(used to display numerals) and the Decatron (used to count or divide pulses, with display as a secondary function).
Xenon flash lamps are gas-filled tubes used in camera
Camera
A camera is a device that records and stores images. These images may be still photographs or moving images such as videos or movies. The term camera comes from the camera obscura , an early mechanism for projecting images...
s and strobe light
Strobe light
A strobe light or stroboscopic lamp, commonly called a strobe, is a device used to produce regular flashes of light. It is one of a number of devices that can be used as a stroboscope...
s to produce bright flashes of light.
The recently developed sulfur lamp
Sulfur lamp
The sulfur lamp is a highly efficient full-spectrum electrodeless lighting system whose light is generated by sulfur plasma that has been excited by microwave radiation. The technology was developed in the early 1990s, but, although it appeared initially to be very promising, sulfur lighting was...
s are also gas-filled tubes when hot.
Gas-filled tubes in electronics
Some important examples include the thyratronThyratron
A thyratron is a type of gas filled tube used as a high energy electrical switch and controlled rectifier. Triode, tetrode and pentode variations of the thyratron have been manufactured in the past, though most are of the triode design...
, krytron
Krytron
The krytron is a cold-cathode gas filled tube intended for use as a very high-speed switch, and was one of the earliest developments of the EG&G Corporation. It is somewhat similar to thyratron...
, and ignitron
Ignitron
An ignitron is a type of controlled rectifier dating from the 1930s. Invented by Joseph Slepian while employed by Westinghouse, Westinghouse was the original manufacturer and owned trademark rights to the name "Ignitron"....
tubes, which are used to switch high-voltage currents. A specialized type of gas-filled tube called a Gas Discharge Tube (GDT) is fabricated for use in surge protector
Surge protector
A surge protector is an appliance designed to protect electrical devices from voltage spikes. A surge protector attempts to limit the voltage supplied to an electric device by either blocking or by shorting to ground any unwanted voltages above a safe threshold...
s, to limit voltage surges in electrical and electronic circuits.
List of -tron tubes
- Mercury pool tubes
- Excitron, a mercury pool tube
- Gusetron or gausitron, a mercury arc pool tube
- IgnitronIgnitronAn ignitron is a type of controlled rectifier dating from the 1930s. Invented by Joseph Slepian while employed by Westinghouse, Westinghouse was the original manufacturer and owned trademark rights to the name "Ignitron"....
, a mercury pool tube - Sendytron, a mercury pool tube
- Trignitron, a trade name for a mercury pool tube used in electric welders
- Capacitron, a mercury pool tube
- Corotron, a trade name for a gas-filled shunt regulator, usually contains small quantities of radioactive materials to set the regulated voltage
- CrossatronCrossatronIn electronics, a crossatron is a high-power pulsed modulator device, a cold cathode gas-filled tube that combines the best features of thyratrons, vacuum tubes, and power semiconductor switches...
, a modulator tube - Kathetron or cathetron, a hot cathode gas filled triodeTriodeA triode is an electronic amplification device having three active electrodes. The term most commonly applies to a vacuum tube with three elements: the filament or cathode, the grid, and the plate or anode. The triode vacuum tube was the first electronic amplification device...
with grid outside of the tube - Neotron, a pulse generator
- Permatron, a hot cathode rectifier with anode current controlled by magnetic field
- Phanotron, a rectifier
- Plomatron, a grid-controlled mercury-arc rectifier
- Pulsatron, a gas-filled triodeTriodeA triode is an electronic amplification device having three active electrodes. The term most commonly applies to a vacuum tube with three elements: the filament or cathode, the grid, and the plate or anode. The triode vacuum tube was the first electronic amplification device...
with two cathodes - Strobotron, a cold cathode tube designed for high current narrow pulses, used in high-speed photography
- Takktron, a cold cathode rectifier for low currents at high voltages
- ThyratronThyratronA thyratron is a type of gas filled tube used as a high energy electrical switch and controlled rectifier. Triode, tetrode and pentode variations of the thyratron have been manufactured in the past, though most are of the triode design...
, a hot cathode switching tube - TrigatronTrigatronA trigatron is a type of triggerable spark gap switch designed for high current and high voltage, . It has very simple construction and in many cases is the lowest cost high energy switching option. It may operate in open air, it may be sealed, or it may be filled with a dielectric gas other than air...
, a high-current switch similar to a spark gap - Alphatron, a form of ionization tube for measuring vacuum
- DekatronDekatronIn electronics, a Dekatron is a gas-filled decade counting tube. Dekatrons were used in computers, calculators and other counting-related products during the 1950s and 1960s...
, a counting tube (see also nixie tubeNixie tubeA nixie tube is an electronic device for displaying numerals or other information. The glass tube contains a wire-mesh anode and multiple cathodes. In most tubes, the cathodes are shaped like numerals. Applying power to one cathode surrounds it with an orange glow discharge...
and neon light) - PlasmatronPlasmatronThe Plasmatron, or technically plasma addressed liquid crystal is a color television display technology developed by Tektronix and Sony in the 1990s. PALC displays combine rows formed from liquid crystals with columns formed from plasma cells, the later replacing the transistorized switching in a...
, a hot cathode tube with controlled anode current - Tacitron, a low-noise thyratron with interruptible current flow
- KrytronKrytronThe krytron is a cold-cathode gas filled tube intended for use as a very high-speed switch, and was one of the earliest developments of the EG&G Corporation. It is somewhat similar to thyratron...
, a fast cold-cathode switching tube